Viewing all customer Discussions for:

Lavatory

Shower door roller

Hi, I have a Jacuzzi brand shower and the door sweep rubber is broken. I tried to replace the rubber but cannot as the rubber strip is fixed in the sweep. The sweep attachment is 21.5 inches long and the rubber strip is about an inch wide. Please advise on the best solution for this. Thanks, Dee. ... (cont.)

The bottom plastic pivot pin for my shower door has broken and I need a replacement part to fix it. The shower was made by Aquaglass and was installed 10 years ago. The frame is 31-1/8" wide. The plastic part is 4" L x 3/4" H x 1/2"W with screw hole on the end and on the side near the pivot pin ... (cont.)

Hi I am looking for the replacement guide for this sliding shower door. It?s a 30 inch door. Thanks

Hello, I need a replacement 3/4" X 24" shower door sweep seal. I have attached pictures of both the extruded aluminum channel and the seal itself to give you an idea of what we are looking for. Unfortunately, I have not been able to locate the seal anywhere. Thanks

Hello! My DELTA single shower door installed in 2013, door has come off frame, due to broken part. I bought home depot, they don't have replacement part. Pls help... SCCC-4872-6mm-U-A Tempered Safety Glass ANSI Z97.1-2009 16 CFR 12 01 II

My framed door is 5/8 thick. Existing sweep is a slip on u channel one like those used for frameless doors. Do you have any suggestions for a replacement? Been looking all over to no avail.

looking to get these parts to reconnect the center false front of my bathroom vanity. No stores carry these. I can use a small L-bracket but would rather replace the part. Its an older vanity so I do Not have a name

This can from the top of a neo angle shower door. The shower door drops down and catches on the bottom seal when we try to open it.

Hi --- Mine looks that same 06095 Quick Learner --- one of the screws rusted and is stuck.. the back of the screw broke off, so I don't think I can remove it --- Based on your response above and before ordering the 24 inch 10-324 as a replacement, can you let me know if it has holes for screws --- M ... (cont.)

Dear sirs: I have a Manhattan Illusion corner shower. The rollers that support the doors are broke. I saw a replacement on your website with the product code 10-076. The part numbers for the existing units are 68037 and 68036. Does you part work for both the left and right sides? Please let me know ... (cont.)

I have 3 sets of 1/4 round showers. Some of the nylon wheels/tyres have cracked and need replacement. I want 6 units. ...................................................... Left to right.. Nylon wheel.. spacer..off set cam (raises and lowers glass when adjusting screw on right is turned)..locking ... (cont.)

Hi I ordered part num 10-061 But I need the insert for that piece where the screw threads into Whick broke what part is that

Shower is made by Aqua Glass. The original rubber strip was replaced by a local worker who got it at a local company and not the original part. This part went bad and was not really suitable. Hope this helps you. I know it is not very definitive on our part. Thank you Jim

I just received my shower door rollers for my Manhattan corner angle shower enclosure but realized I don't know how to put the rollers on the track. Each side panel has two screws at the top of them, do I remove those screws and then pull out the top track? I don't want to damage my enclosure and mi ... (cont.)

Trying to identify and buy the rubber part that goes in this assembly

This is from a curved shower door, attaches to the bottom of the glass to guide the door as it opens/closes. Wondering if anyone knows where I might find one to replace. Any help would be appreciated.

My rolling shower door has a roller at the top and a guide at the bottom. Do you have this piece? See the attached photos.

Is the 24 inch the smallest length?

Does the shower sweep come in 44 inch width? Thanks