Viewing all customer Discussions for:

Lavatory

Hello I am looking to find a replacement for a rubber seal for the shower door. Can you please suggest a product?

What is the obround hole center measurement of SHOWER DOOR LATCH, product Code: 10-110? I am looking to replace mine, it 15/16" H.C.

here is a picture of mine the drip pan is on the inside of the door and I need to know if this one will fit mine because from the left end to left screw is about 3 1/4 inches and on the right screw to right end is 2 1/2 inches. And from screw to screw is 20 3/8 inches apart. And the tong is ... (cont.)

We purchased a 32x32 corner round shower a few years ago and we have misplaced the parts. We are told it is a max shower kit. The class is 3/16!inch thick with four panels rounded and each panel has two holes on top and two on bottom we just don't know what type of wheels and gliders to purchase ... (cont.)

These roller brackets go on a curved shower door and are missing from the bottom of the doors - I'm assuming they're the same on the base of the door as well?

I can not locate double side tape for shower seep installation. Please guide me. Thanks

Do you have this part? It's for a shower door! I askyou before and I bought he wrong part! Can you help me please and anwer my request!. I need 2 of this part! Thanks so much!!

I am trying to replace a shower door flap for a 20 year old Aquaglass Shower stall. I ordered Item #10-319. It fits in the slot of the drip piece but the flap portion that keeps the water in the shower is about 1/2" shorter than the original part and allows the water to leak out. Any suggestio ... (cont.)

Hi I can't find a chrome door sweep 25.25 inches long. Fits on inside of shower door with screw holes about an 1/8 inch from the very ends.it does not have a plastic sweep attached. Please help. First picture s front and second back

I am looking to get a replacement seal for bottom of shower door. The shower door is a 24 3/4 inches. I may end up replacing the entire dripedge. The hinge on the door is on the right hand side when looking at door not sure if that matters. Please advise.

I have a glass king shower door and the top roller has broken. Your 10-058 seems to match the top roller but the bottom is different. I have pictures attached for your review.

for 3/8" thick glass

1- what is the best way to remove the door frame assembly screws 2- what to do if the screw head breaks off 3- how to unsnap the 10-216 guide from the track thanks

Hi this part is for an RV bathroom slider door. It measures at: Outside Diameter: 1 inch Inside Diameter: 5/8 inch Side Diameter 1/4 inch. Please help!! Thanks, Angie

In our church we need to replace 2 bathroom partition concealed door latch knobs. The ones we have now are a hadrian. Are knobs inter changeable or do we need to use hadrian brand? I have picture of the door know opening (minus the latch, if helpful.

The shower unit is about 20 years old. The door is fine I just need the plastic joint that I show on the attachment.

Roller broke that holds curved glass shower doors from kit bought at Home Depot there is no number on either part or the door. It says King on the door

I have a cheap plastic drip cap shower sweep that's broke. It was put on with glue. I was wondering if you had one that didn't have the screw holes like 10-324.

Does Swisco have the parts for this towel bar that attaches to the outer frame of these double sliding/bypass shower doors? Assembled dimension: 23-9/16" long x 1" tall x 2-1/8" deep. Towel bar dimensions: 20" long x 15/16" tall x 3/8" deep. Bracket dimensions: 1-3/4" wide x 2-1/8" deep x 1" tal ... (cont.)

I have a Maax Talen curved shower. The bottom guides are broken. I contacted the manufacturer and I am told this item is discontinued so they do NOT have replacement parts. They told me I would have to replace the doors for $350.00!!!! I told them that is ridiculous for part that should cost a few d ... (cont.)