Viewing all customer Discussions for:

Other

Window grid Part #. 9038801 Measurements. 281/2?(W)x 24?H

I recently ordered and repaired some metal windows with the info I found on your site. I was hoping you could help me identify and order this retaining clip for the screen shown here. Several have just wore out and I would like to replace. You have done an excellent job with your website and doc ... (cont.)

The only number have for this window latch is the Pat number 5, 139, 297. There is an 08 on the back as wellDennis

Looking for replacement for this operator, has 7D100P marked on the one arm and truth marked on the other.

I need a replacement crank unit. there are no marking on the window or the crank. i do not know the manufacturer, i just need a replacement, can you help?

Exterior door handle broke 3-15/16"

Replacing window channel balances in my house for 10 windows. All channel balances are 29" long and 9/16" wide. Thank you.

Hello, I have 5 condos with BETTERBUILT aluminum windows and I need to replace the Channel balance in all of them. I need to identify what part I should use. The windows are square9 30.5x30.5, and the metal part on the channel measures 29"and its 3/8"thick. It has a marking stamped on it 28C 7. Than ... (cont.)

Hello, I have several patriot windows with broken shoes. I have been searching your site for replacement options. Looks like the full balance replacement is the best course of action? I have 26b balances. Can you please point me in the right direction? Thank you! Jeb

Need a new door bottom/sweep for an in-swing patio door. The glass is marked "insulshield", which makes us think it's a Pella door, but there are no identifying marks otherwise. It's two French doors, one fixed, the other in-swinging. The door measures 1-7/8" in thickness. The existing piece app ... (cont.)

Hello, I am looking for channel balances for 2 different windows and would appreciate if you could help me determine the correct ones as well as pricing. I included some pictures and below is the information I was able to retrieve after removing them: Window 1: Brand: BSI Stamping: 353 ... (cont.)

Can't tell between the type whether it's Encore or maxim.

1) 33-109B : Andersen Bolt (1) 88-014 : Andersen Exterior Pull Handle, 5-1/2" Handle did not work on the existing Anderson sliding door. The old handle had screw attachment points closer to one side and the handle I ordered had holes centered on the door plate. 5 1/2 inch spacing between the holes ... (cont.)

Hi, I need a replacement mortise lock for an Atrium Vinyl Sliding Door. The part number is PM520A. I have attached some photos of the part with some approximate measurements. Would Part 82-239 be a suitable replacement? Would you be able to source or sell the exact same replacement part? I liv ... (cont.)

I have Norco casement windows about 13 years old. I need to replace the hinges on two windows - a right hand and left hand pair. The operators are kind of loose and I would like to replace them also. I like the style hinge that has the offset adjustment nut to align the sash in the opening. I also ... (cont.)

Can you recommend a replacement part for this balancer?

I have pivot 15-192 listed to notify me when parts are available. My question is do I need a tool to remove the pivot and spring assembly? Do you have the tool available to remove and install the pivot/spring assembly? Thank you.

The Dimensions are 1.5" dia wheel roller. 1 7/32 sheet metal height, 2.600" from end of sheet metal to offset in tab. .730" in width. Can I get a 1.5" dia roller, and a truss rivet to do the wheel repair on my own? I would like to purchase the assy if possible, but welcome your input. Thank yo ... (cont.)

I want to replace some or all of the parts of a Pella storm door latch (Pella branded) shown in uploaded photos. The exterior handle and cover plate are weathered (storm door handle 1) and I want to replace them for appearance sake, with either polished brass or white finish parts. The latch operat ... (cont.)

I am searching for replacement parts for an old trolley bus windows. In the one image I have pointed out the tiny part that is broke on most of them. If possible I'd like to just replace broken part, but will replace entire latch if necessary. I hope you can help or point me in the right directio ... (cont.)