Viewing all customer Discussions for:

Other

The screw is key to holding glass in place. Don't know where to turn. It is standard door on a track. The house was built around 1986, and it has a name plate by the front door in the cement, HOMESTEAD. The development is called the Pointe in Glen Cove.

Hi, I have a wooden center monorail guide drawer slide that needs to be replaced. The unit is: - 16 1/2" in length - width at the ears 1 1/8" - width at the neck is about 7/16" - height at each end 13/16" stepping up to 3/4" through the center portion (I could make either height work. - There is als ... (cont.)

i have a door handle that is dark brown in color with the following numbers nw1720-1, -2, -3, -4. What handle will work? thanks.

I have a patio door by Traco and need a new handle/lock set. The numbers I found are: Traco AnsiZ97.11984 16 CFR 1201 II sgCC-1308 1/8 Any idea what handle I should order?

I have a milguard window balancer that broke. It measures 27 inches in length (metal piece only) and the width is closer to 5/8 inches. The markings on the metal is stamped 26 4 JV CMC 7. It looks like S380, S385, or S395 may be the correct replacement part. Please feel free to provide advice ... (cont.)

I have, what I think, is an Atrium residential window that was installed around 2008. The plastic counter balance block at the bottom of the window has failed/broken and I am looking for a replacement for it, or for the entire balance itself. Series: HI-D 2500 SH P.L. #529-016 The balance ha ... (cont.)

Marking: 18 3 BSI Metal to Metal: 18-3/4" channel width: 1/2" Bottom shoe doesn't match to any of your products. Dimension 1-3/8" x 1-1/8" x 1/2" Please help recommend the equivalent balance to order.

Sash jam assembly that attaches to the bottom of the sash on the right side when viewed from the exterior. It is 7.5 inches long by 0.5 inches wide and has pivoting arm 5.5 inches long by 0.5 inches wide and has a pivoting end piece that travels in a piece attached to the frame.the window is a serie ... (cont.)

need a source for new aluminum spline material that will fit anderson 400 double hung screens. existing channel measures approx 0.220 inches wide

Awning Window crank 1/2" Home built in 1972 so standard cranks too small

Would like to know if you have this part

I have an historic house with metal double hung windows that say "NU sash" on the lock. They have an elaborate pulley system on the top inter workings and heavy cord connecting the windows. the cords are "slack" or broken as a result of the spring/block and tackle system has frozen up. I can only ... (cont.)

Keller rollers #8888. Can you help?

I recently bought a mid-century modern house and it has original Arcadia dual aluminum sliding glass doors that are huge and in need of rollers and weather stripping. The prior home owner kept the original receipt for the door which has the door as Arcadia ALC-1 #4522. The dimension is 15' 9" x 6' ... (cont.)

Doors from about 1988 need roller replacement on rear of sliding patio door Wood inside steel outside Was given a part number of 0fat0000 but can't Find anything under that

I have an aluminum frame with screen. two corners snapped corner keys measure .205 square. made of cast aluminum with spring cl.ip on each end. each leg measures 1"

Hey, Springs have a tendency to sing when you release or place strain on them. I think oiling them will reduce this. Would you suggest oil or grease? This is important since, I don't want to look at them again once they are installed.

Mirrored sliding door roller. Doors manufactured by Arch, 1988. Roller wheel broken. Plz see attached photos of roller assembly. Thanks

One balancer failed and was discarded. The one remaining is functional and we wish to match it and reinstall the single-hung window. Which "S" item would match the one that we have? Thanks in advance! The ID on the functional Milgard balancer is: "32 5 BW CMC 2". The length of the metal port ... (cont.)

Hoone 14" drawer slide