Viewing all customer Discussions for:

Other

Hi, I'm looking for this guide that fits into the bottom groove (4th pic) of my 6-pane double hung wood windows. Thanks! Nicole

The pin is 4 1/2" long. The picture is from another door. I would use this one but cannot get it out.

Dear Sir or Madam,Reading the previous posts from Austin Texas, it looks like I also need part S395-28 with the 2740 option. Can you please tell me if this is correct? Also, is the the correct link to this product: https://www.swisco.com/28-Series-395/pd/Series-395-Channel-Balances/S395-28Thank you, ... (cont.)

Seeking seals for wood sliding glass door. It's the seals where the door meets when closed. Cannot locate brand. Sticker on glass says Tempered 16 car 1202-cii ANSI z97.1-1984 1/8u soccer / 1436 8s6206a Seal is 78" tall, 3/4 " thick, 1&1/2 wide

The glazing pictured comes from a transom window. Bottom 1" Vertical 1/2" Return 1/2" with rubber gasket Need approximately 350LF to repair failing components at an apartment building in Raleigh, NC.

Plastic piece that covers the balance on my window

Bad hardware on a vinyl casement

Hi,I have 7 Marvin Windows - all were installed in 1986 when we built the house. All are the same except the sizes. The sashes tilt inward and can be removed for cleaning.Lets start with just 1 window:The metal in the window is stamped with: "Marvin-01-IGCO r CBA 86" (see picture).The Balances ... (cont.)

Will this work on a Andersen thumb latch Part Number: 1997189

having problems with the window staying up and the pivot doesn't come back up with the window was thinking it was a bad pivot lock shoe. please advice. thanks chris

the only marking is a 5 on the top coil and a 6 on the bottom coil. 12 of these need to be replaced in 6 windows. Do you have the assembled unit available? The window weight is 20lbs, the window length is 29". Coil thickness is 0.510". The overall length of the plastic piece with the 2 mounting h ... (cont.)

Hello, looking for parts. Specifically pivot shoes. Do you have parts for this model? Thanks! Chris

Window was installed in 1992. Number on bottom looks like 7?08 and 07900 on the arm.

Cab you tell me what rollers are used on my sliding glass door based on the information I found on the lower left of the glass (shown below): PPG Herculite K Tempered Safety Glass BS6206A ANSI Z-97.1 1984 1/BU 5NCC-250 6013687 Thanks Very Much

I am looking for the arm that goes from the crank to the window. The brand name is Roto. I do not see any model numbers. If I can't get just the arm, I will take the crank and arm. The hinge system seems to be fine. I actually need four arms.

Good morning, I am looking at replacing this part that fits a spyral balance. Overall dimension are 22.5mm wide, 50mm high plus 5mm for the metallic piece coming out of it, and 13mm deep. The plastic piece says "patent 4610108". Thank you for your help.

Hello! We had hail damage to the glazing beads on two patio doors. I don't think they are Anderson, because I don't see their logo etched in the glass (all I see on the window is the Herculite glass etching). I'm attaching a photo of the label on the door frame and pics of the window damage. I hope ... (cont.)

I need a whole new two point locking system with a 15" bar. Also the plastic clips that hold the bar in place. I also need 2 lh operators and 1 rh operator.

I'm attaching some photos of my spiral balances from 1961 aluminum windows. Can you tell me what the best replacement is for the balance itself as well as for the shoes? Note the clip on plastic that keeps the window in the channel. Thanks!

Your part number 38-210. Will this work for my Truth sash lock 21328? And can you just replace the white plastic piece or do I need the whole lock assembly? Because I am not sure the white plastic piece and pop out and a new one put in?