Viewing all customer Discussions for:

Other

Balances are broken

Nami NFRC 100/200 Code:HII-1 Rating:NFRC Series:CLCASE NST:2650 NFRC HII-1-006-7/14-15 97M Window opens but will not close, crank spins with a clicking sound when trying to close. I *think* I need the part shown in the attached photo IMG_1245.jpeg, but please advise as to your opinion regarding ... (cont.)

I need help finding this kind of window balance coil online. Can you guys please provide me with some options that might be relatively close to this one.

Looking for replacements. Balances on both sides of the window are the same. The numbers on the balance are 11600-17 and P78 12#27 1-86

The lock busted on my sliding door and needs replaced. Please advise. If possible, a keyed or number key pad is preferred. Thanks in advance! Best, Chad

Please see part number on window for replacement parts for window in a home that won't stay open. Any help would be great

Hi. I recently called and was told to send in some pictures of the weather stripping that I'm looking for. I have a few pictures available. My measurements are that the base came out to be 1/8th of an inch. Thank you for your help

Pella casement

I am looking for the attached part. This is for the Series 8500 Silverline Windows.

Hello, I hope you can please help. We have several broken coil balances, but I'm not sure which style or series is the correct replacement. We could not locate any stamps or markings on the coil. Attached is a photo of an intact balance. Can you please advise what series or style to use or what ... (cont.)

I already ordered the wrong parts (15-192) They look very similar. The dimensions on the drawing of the (15-192) appear to be correct for my frames, but the new shoes have small guides that prevent them from fitting into the track. The present shoes have broken due to corrosion from contact with Se ... (cont.)

Can you please help source this window balance for a tilted bottom windpow? Approx 30 3/4" long & 1/2" deep. Non Tubular. Manufacturer : Ply Gem Window - 1500 series

I miss placed the parts. Photos are what I have. Numbers you gave me are:S600-19 blue tip75-006 tool15-046 foot. Slot is approximately 1/2"Found the parts the foot is 1/2".

Can only find this stick on the window that looks to be associated with Swisco. Need to replace the lower slide due to the dent in the grid and broken window. Do you sell this part or the whole window? Thanks, Joe

Good MorningI just disassembled the lock in my storm door, for which I do not have a key and is in bad condition. I could replace parts or the whole thing, I am inclined to do the latter. It says on it "patent 4.578.967" and it looks similar except for some cosmetic differences. I will verify the m ... (cont.)

IMG_2474 this is the same mechanism but in a different room. Ignore the small light. IMG_2478 is the window in need with the mechanism remove. The window swings in and out from the top. The rest are images of the mechanism I removed. I would like a more modern and easier to use part. If that's possi ... (cont.)

Hi, One last window latch I'm trying to match and replaced, "Viking". On the latch: 2 1/8" holes on center. 11/16" hole on center off the edge. It is 2 7/8" long and 1" - 1 1/16" wide. I would want to replace the latch base as well. Thank you! Anna

I have an old wood Atrium door patio door. The vinyl glazing bead is broken and I can't find a replacement. I attached a picture of it's cross section with dimensions. Are you aware of anything out there that is close to it. Thanks so much.

Purchased these windows in 1994 and one of them had a seal that wrinkled up.Can you help?Tim

I can't read the final letters/numbers on the assembly due to rust. I think it is ZO. Those last two appear to be letters as they were thicker than the numbers. We have not removed the assembly so I don't have a picture of that but we did take off the "cap" hiding the mechanism and I've sent a pi ... (cont.)