Viewing all customer Discussions for:

Other

I need some replacement roller similar to this.

Our door has no manufacturer info. It is a generic sliding glass vinyl patio door, 60" wide, with one door stationary and the other sliding, left hand slides when viewed from outside the home. We need help with a couple of parts. (1) At the top end face edge of the stationary door where it is besi ... (cont.)

Good morning - I ordered channel balancers for my window - they match exactly the ones I needed to replace. My order and part number should be on file. However, I can't get the window back in. I need about 1/8th of an inch more to clear the right-side frame. Do you have any tips and tricks to h ... (cont.)

Prism Window balance shoe

I don't know for sure, but I believe these are tilt window latches from American Craftsman which in turn was bought out by Silverline, which in turn was sold to Ply Gem. Anyway, my house was built in 1974, so these vinyl windows were installed sometime there after. I am looking to replace these win ... (cont.)

I am trying to find replacement hardware for some doors at my moms that were build in early 1960's - I specifically either need all new hardware that will work for two quardofqld doors or three replacement rollers and one top pivot stop. But I have no idea where to look. I think the width of the ro ... (cont.)

I have a legacy storm door with a double bolt mortise lock with centered latch. The lock is broken. can you help me find a mortise lock replacement. the door is burgundy in color. i will get a brass door lock. Please find attached a picture with some measurements.

I have lost one of the screws to my basement slider. Can I buy a replacement screw? If not - what would I have to order? I have attached the sticker that was on the slider - Series:311/312 SGD. Dimensions are on the sticker. Thanks for your help. Don

Hello. I am lost. I am going to send some photos. I need 4 balances. 27-4 is on the stamp Please see photos and help me order the right parts.

I need the mortise lock only for Atrium Swinging Patio doors, Type: EDSL, Code: ATR-K-1. My trim and handles are fine and do not need to be replaced.

I am looking for a set of tilt latches for a Superseal vinyl window. Can you help me? I have included the window label, a photo of the tilt latch and the measurement from the side of the sash to the sash lock.

I have a sliding glass door with a latch that doesn't work. I'm thinking that I need to replace the handle and mechanism? Any help you could provide in identifying the replacement part would be greatly appreciated!

Hello I am looking to purchase approximately 440 Ft of snap in glazing suitable to replace the glazing bead pictured in this email.

I have several BSI window balances to replace. I did not take photos while any of them were installed (it is from another location out-of-state). The parts needed are: BSI 26-2 (two each) BSI 16-1 (four each) I have included photos of the part numbers, and photos from each end of the balance (th ... (cont.)

pella 9040302 rh hindge

I am looking for a replacement part. The part is plastic, 3.5 inchs long and 7/8 in wide.Thank You Victor

I need these parts for a casement window.

The upper sash balancer rods have started to fail 2 this past weekend. What short term solution can I employ to keep the window up? I currently have wood corner trim inserted under the sash in the track but am concerned that the point loading will damage the bottom sill trim. As the windows are lar ... (cont.)

I am looking to replace broken window screen corners. The corners are 3/4 inch and the part that inserts into the metal frame is 3/8 inch by 7/16 inch. Swisco part 95-270 looks close but I don't see all the measurements.

I need to repair a couple of metal windows and cannot identify the parts I need. The windows were installed in 1997 and I cannot locate the manufacturers name. I have been told they were manufactured in California and the company no longer exists. I need glazing channel that appears to be very si ... (cont.)