Viewing all customer Discussions for:

Other

Hello, just wondering if you can advise on how to replace. Thank you.

I have these old block and tackle balances in my windows (circa 2001) and some of them have failed. Mostly, the shoe has failed - it's jammed and in some cases damaged. It's an unusual shape of shoe, not a t-shape but rather a single sided sort of cam shape, as shown in the photos. This one is undam ... (cont.)

across front 5/8 top to bottom of front 7/8 length 2 1/8 single roller looks like roller measures about 1 1/8 but really worn out. room build in 2000 by patio enclosure out of Houston Texas

I am reaching out on behalf of my client. They need to replace the springs in one of their Peachtree windows. The window isn?t opening/closing properly. I cannot find a CT based vendor that carries this product.

Pin at bottom of multi point lock broken off or missing Jeld-Wen window alum clad wood need new he'd.can you help

I just received the correct b&t balance, thank you but discovered a broken top ash guide. It is 1 1/2" long, 9/16 deep, & 5/8" wide. I didn't find an exact match in your site but if it can be special ordered or a top sash that will work if possible. Thank you for the help

Attached are pictures of my window balancer. I need help trying to identify them.

arm # is 20755 on each see pictures of latches how does one attach the latch for the window - some of our window latches do the following - open the latch it locks the window and when the lever is closed it opens the window - eas it put in wrong (obviously) - how do you correct this problem - are l ... (cont.)

This window weather stripping is 32" long (obviously cut from a roll) and 1/4" tall with two angled fins/barbs and a 1/4" foam filled round core. I show a picture of the profile above.

Its 1/2 inch wide 1/4 inch is pushed inside. Gray . If you don`t have it could you name it.

The first is a 27-3 AK5 CMC 50 (non tilt windows) the metal is 28" in length The bottom are both pinned in place plastic piece is just a fraction that I measure over and inch. The second is an 27-4 G15 CMC 50 (non tilt windows) the metal is 28" in length. Attached are pic's for both, let me know ... (cont.)

29 x 9/16 x 5/8 2830 JL stamped on side BSI Sash weight ~24 lbs

I I need to replacement for rollers for my windows

I need the pivot bar that was broken off the bottom of both sides of my window. It looks similar to this, but with a different end treatment. https://www.swisco.com/Simonton-Pivot-Bar/pd/Tilt-Window-Replacement-Sash-Pivot-Bars/26-336 Also, my spring saddle part and barrel part is broken. the wind ... (cont.)

Hi, I am looking for replacement patio screen door roller replacement. The diameter of wheel is 1.125 inch. thank you

I received this order and realized I actually need a triple coil system. My first question is how do I go about returning the 4 single coils ordered? Second question is how do I go about finding the correct triple coil system for my windows.The broken parts are still in since I would like to not tak ... (cont.)

The area was competent enclosed around the channel balance! I had to let open the area to reinstall (after having pried it out of the channel. It was very difficult! And then I had to reinstall the foot at the bottom! I basically damaged the channel, permanently deformity some areas! There has to b ... (cont.)

Looking for replacement handle - Middle to middle is 3 5/16. Height is 3/4 width is under 3/4.

I have a CertainTeed bathroom window approx. 25-30 years old. Do you have replacement parts for the spring cover -tilt pins etc.?. The tilt pin on one side is loose and slice back into window on one side and I believe the spring steel is shot or off track because the window does not stay up. I can f ... (cont.)

I need to purchase a small piece of plastic that fits on the side of a window screen that clicks onto the side of a screen that keeps the screen in place.