Viewing all customer Discussions for:

Other

2 pieces, assembled on top of each other. Screws are threaded into a metal jamb. Hole separation is about 2 1/8". Length 2 3/4". Width 1 1/4". Writing looks like Jernes or Ternes xxxDIFRAME, Industry, CA Thank You! I cannot find a replacement.

I am looking for replacement parts for mirror closet door guides roller and top and bottom track. The only numbers I found are on the roller- Del Mar 448-3.The nylon roller is 1 1/4 in. Dia.

Hello, As you can see, I purchased the S140-10 quick tilt single. I ambwriting because I need to order 2 5 pounds of similar nature and 2 2 pounds of a similar nature. However, I need the coil to extend with constant force up to 32 inches. The one I have does not extend to that length. If possible ... (cont.)

Need to know if you have windows handle

I have 5 windows that need new balances2 = 27 1/2 x 9/16 plastic 1 1/6 STAMPED 274 1 = 30 9/16 X 9/16 Plastic 1 1/16 STAMPED 304 2 = approx 24" (cant get window out) assuming width & plastic same STAMPED 2430NEED 10 total balances but not sure which ones I need. Thank you!Please call me if you ... (cont.)

Vinyl sliding window latch/ lock

I am needing two of these pulls for windows that are missing them. Not sure where to start and having no luck online.

Hi, I am looking for a replacement for a Unigrass 6600 22 inch drawer slider with an "L" ending for an in-cabinet drawer. The drawer is a shallow tray for pots and pans that fits in a double wide cabinet below a cooktop.

1994 built South Carolina coast house. Any help would be great. Thanks

I need a replacement latch for a Renewal by Anderson 2003 tilt in window

Looking for the replacement string or cord for my pella windows with mini blinds. See picture attached

latching 36" wide storm window on a colonial house. Currently 35 yr old plastic. Windows mfg by possibly "Solaire " not sure. About 23 sets are needed.

The originals in picture say RONTHOR NYC with a T under the round 1/4" diameter peg. Overall about 1 1/8 x 1/2 x 1/2. Probably 30+ years old. What is the replacement for these? Also is there a metal version or equivalent? Thank you.

Hello!I was referred to you guys for older window cranks. I have uploaded the photos of the crank(s) I am looking for. I need one that allows the window to open to the right hand side. I need one that allows the window to open to the left hand side. Can you help!? Thank you James ... (cont.)

I am trying to replace some parts on a Jeld Wen Double Casement Window that was installed in 2012. Unfortunately, all of the identifying information has been taken off of the window and we do not have the original order records. The right side of the casement window is fully operational whereas the ... (cont.)

It is stamped as Truth 45275. The arm is stamped with 40267. Total arm length about 9.5" 4.5" from the end to the bend in the arm. Thank you!

I've got three mirrored closet doors on wheels that run on parallel tracks on the floor. The track rails have worn down in the middle and that section of the track has sunk/bent downwards. So when the wheels go over that section, it comes off the track. The wheels still seem in good condition, I'm h ... (cont.)

lock has patent number 5,139,291 on back and 7C 2 3/4 " long, 11/16th wide, 7/16 " high Slides into the top rail of lower sash. Need RH and LH parts

The upper window casement mechanism is broken. This is on the left window as you look from the outside. The second two pictures are the broken piece. The first pic is from the right side to show how it is supposed to look. The plastic slider piece on the left side where two arms attach is broken. ... (cont.)

Enclosed please find images of a 2 point mortise lock that needs to be replaced. First image. The distance I need is 6.5" long for the top and bottom screw holes. Most I've discovered in my search are 7-13/16" long.