Viewing all customer Discussions for:

Other

CGI PART # HD-72-10061 MULTIPOINT LOCK, WHITE CGI PART # HD-73-10082 AWNING OPERATOR TRACK SHOE

Need 2 duplicates.Please searchHome built in 1960'sThank YouPatty

We need a replacement handle and rollers for our Acorn Dorwal 8' patio door. Our condo was built in 1991 and this is the original door. It's too cold to take the door off right now to show you the rollers but I'm sending pics of the handle. A security sticker on the jamb says Series 1200. I don't kn ... (cont.)

I need to identify and order replacement Pivot lock Shoes for my tilt-out window. I attached photos of the existing Pivot Lock Shoe. There are no markings I can see on the piece. The dimensions of the shoe are: 1-1/4" tall X 1-1/4" wide X 1/2" thick. I also need to order counterweights for the ... (cont.)

Dear Team, I would like to replace the side locks of 4 windows as they keep getting stuck when you try to open them up to be cleaned up. Do you have this model? If not, do you know where I could get them? The length is 3" while the width is 1.5." The height is 3/4." I hope the pictures help. T ... (cont.)

Looking for this particular window lock. Thanks

1. It's is only 1 window it ha springs broken on both sides. 2. Spring width is 1/2 inch. Window is 10 Lb. 3. The stamp on spring is "5" so I suppose I need 2 x 5.5 Lb springs. Do you have exact pivot shoes number in case I need them I have ordered 2 x 5.5 Lb 1/2 inch wide spring coil balance. ... (cont.)

need entire handle

Hello, I have these doors and was hoping if you could help me find the right track for them? I was searching on your website and I found these. Is this the right part? Do I need 2 tracks? One for top and one for bottom? https://www.swisco.com/24-Low-Profile-Track/pd/Bifold-Door-Accessories/21-45 ... (cont.)

need 2

I have about 20 windows totaling about 50-60'

Good morning. I need to replace vinyl bead glazing for five windows, but neither the manufacturer nor the brand is listed on the windows. I spoke to an agent who said you may be able to help if I sent pictures of the glazing. Let me know if you have any questions. Thank you

Trying to find a flexible window glazing bead that can be used around a sunburst window. My single hung windows are Kinco but I can't identify the stationary sunburst window the bead goes on.I appreciate any help you can provide.Ken

I have a Vetter Sliding Patio Door that was installed in 1996. I need to replace the mortise lock ONLY but will purchase a complete handle/lock package if necessary. Two pictures are attached: Pic1 shows the complete handle/lock. Pic 2 shows the only identifier stamped on the side of the lock (i ... (cont.)

I have PGT windows in my home built in 2008 and a channel balancer on one of the windows (model H35 SH) has failed. There is a number 29 on the broken channel and from what I've seen on internet, a replacement part can be identified from that number. If that is correct I'd like to order a replacemen ... (cont.)

Looking for two replacement hardware pulls for our Thomasville bedroom chest of drawers. See picture. 7" total width and attachment posts are 4 3/4 inches apart.

Allen key to open lock. the window swings out with hinges on the top. when you twist the lock it has a metal bar that swings out.

I had ordered (#2012161) 5/8" Top Sash Guide, Kinco as close as I could determine to work but won't work as top too small. The old ones were square on bottom and broke out and mechnikisum jamming up... The old ones are 1 inch by 15/16 wide I installed new ones and seeing the spring mechanism come ... (cont.)

Would like to get this in dark brown.

Need new roller set please