Viewing all customer Discussions for:

Other

I need a window lock similar to the 90-005 but with a 5/8" throw. Does anything like this exist? All dimensions for the 90-005 work for me with the exception of the throw. Needs to be 5/8". Thanks

I currently have the below and need a replacement set, the measurements from the center of screws on the inside handle is 3 15/16 and my outside handle has a cylinder lock and keys. Inside Handle has a part of 1060-1943 Outside has a mfg name of Sash Controls Inc, Part #1963.

Hi, trying to find the parts to fix my parents window. I am fairly sure the Pivot Shoe is this ( https://www.swisco.com/CertainTeed-Pivot-Shoe/pd/Tilt-Window-Replacement-Pivot-Lock-Shoes/15-192 ) but I don't see the same Sash Pivot Bar anywhere. I also can't get the coils out yet because I didn't ha ... (cont.)

I'm looking for some of these sash cams.

I'm looking to order new weatherstripping for my windows or to fill the gaps. The strip is 30 inches long and 1 inch wide. see pictures.

I think my patio door might be due for new rollers, but I don't know how to get at them. What do you see here? It doesn't look like I can reach my wheels.

I NEED TO ORDER TWO REPLACEMENT CHANNELL BALANCE FOR MY WINDOW.

I'm having difficulty finding a 4" bore hole replacement handle for my old storm door. This storm/screen door was put in some 20 years ago when we built the house. (I think we purchased from Sears at the time). Do you have a replacement handle for my door? Thanks for your help! Jo ... (cont.)

we need 4 bar hinge sets - 10" for one of our customers. I found CRL - DSH10? Do you guys carry something like this?

I would like to replace a broken spiral balance. Are the dimensions 5/8" x 30"? Is it best to replace both sides at the same time?

Model # 7436 Part # O Lower Guide Are parts for this unit Still available? Bought in 1996.

Hello, I have a Cole-Sewell storm door, probably from the 90's. The lever has broken. The metal nub that kept the tightening screw on has worn away. The inside back plate measurements are approximately 8.25" x 1" What replacement part would you suggest? Thanks

I have a Kawneer door that would have been installed in 1975. I have been looking at your pivot sets and trying to determine which one I need. The closest match is the 79-128 I believe. I have not had the door apart but the hole pattern for the top piece matches and the outside is the same shape (f ... (cont.)

I have a broken channel balance. The length of balance metal part is 26 inch. The width of each shoe is ~1 inch. The writing on balance is "25 3 DX CMC 11". What balance do I need. My window is not tilt. Also if the balance is not correct what is your return policy?

Good morning, we have had a vendor go out of business and are in need of hardware for three of the following doors as soon as possible. Any help would be appreciated! Aluminum Clad Wood Inswing Patio Door Stile And Rail Door Right 37.75 x 86.5 3-2 x 7-2, Door Panel Width = 35.875, Door Panel Height ... (cont.)

Is this available in store

Hi, Have single hung window, need pivot shoe + coil spring & it's case.. thanks!

Hi! Thanks for your help! Here are the measurements of this roller: Length: 2-1/6" Width: 5/8" Height: 1-1/8" Wheel Diameter: 1-1/4" I don't see any numbers or markings. Let me know if you need any additional info. Thanks again! Best, Steve

Hi Swisco,Great site! I hope this works.I have a set (bay window set?) of Anderson casement windows. I attached photos of the left hand side window with a measurement. But, I need the right hand operator.Can you guys take a look at the picture and let me know if this is available and the part nu ... (cont.)

This a pin that inserts into the balance glide in the sash. It is screwed to the lower inside of the window itself. The windows were installed at the time of construction by Ryan Builders an 1991. the material is pot metal and I have several of these broken in the same spot. If I can find them I cou ... (cont.)