Viewing all customer Discussions for:

58-022 White Pile Weatherstripping, 9/32" x 9/32"

I've been looking around for weather strip for my window but ca't seem to find. Do you have this type. Pictures included.

The "T" part of the strip is 1/4" not 3/16". I can not find it on your web site. I contacted the manufacturer and they gave me your name. If this can not be replaced with a like item, any suggestions?

I have spiral tilt windows looking to change pile weather stripping, white preferably. Do I need to be exact; can I be off by a 32nd on the base? Pictures are attached. Also the top tilt latch screws are stripped; what can I put in screw holes to remedy?

I have four pairs of Alcan sliding glass doors that need the white weatherstrip that seals the edge of the door on the outside and inside when closed. Attached is a cross section photo. The width of the "T" is approx 5/16 inch wide and the bulb itself is about 5/16 in diameter. You can see in the ph ... (cont.)

looking for above part to fix my sliding door

I have white pile weatherstrip (9/32" x 9/32") that came attached (glued) to a plastic backing piece that slides into my window screen top edge. I'm attaching a few photos of the plastic backing piece to see if you sell a replacement part. It has cracked and is no longer usable. I need a replacement ... (cont.)

hello, I want t order the correct size weatherstripping and i'm not quite sure on the size/part #. Please advise. I am including pics. White pile/ with fin. Thank you.

How do l measure for the correct size to fit the channel?

Hello! With the attached photos, I need help identify my window weather stripping in the picture, if you have it or do you offer something in its place? Channel = 3/16th" wide Brush = 3/8th" wide

Part 58-022; white wool 9/32 x 9/32 weatherstripping This part appears to be what I need. I have 25 year old windows - on some of them the weatherstripping on the inside of the bottom sill have broken or come out of the track. Because the lower sill is a fixed part of the window frame and can not ... (cont.)

Could you tell me the thickness of the seal? I believe mine is 030" x .270 x .270 and white with a black stripe down the center. Thanks, Gary

I'm looking to replace the broken seals and weatherstripping in many of my windows. I don't see a manufacturer on my sticker. Two sets of windows purchased at different times but same manufacturer.

I purchased WindowDepotUSA windows in 2007. It was manufactured by AccuWeld: which was bought out: but warranty and support issues: are not supported. I need to replace the weather stripping on two large sliding windows: it appears the stripping is "worn, twisted" and needs to be replaced. Without ... (cont.)

My granddaughter recently purchased a house and we determined there were issues with some of the windows. They are double hung tilt windows. We were fortunate enough that there was some documentation left at the house that showed the purchase of the 25" series 600 spiral balance (S600-25) from you ... (cont.)

I have alenco sliding door and im looking for the the weather stripping??long fuzzy strips

Please find model numbers and pictures. The condition of the existing weather stripping is such that I can't tell if it one piece or two. I would like help identifying the replacement part(s) and instructuctions on how to install it.

Not sure what size this is or what I need. Weatherstripping for bottom sash

I think this is Kolbe door, circa 2001-2002. The seal/gasket is brown. It needs replaced; it is torn and falling off the rail.

I have a sample from a window that measures about 1/4" wide x 1/4" tall with a fin in the middle. I'm not sure if a 9/32 will fit, it was tight pulling the "8/32" piece out. Will a 3/16 base work or will it have too much play? Also will 3/16 height be too short? Please advise. I have 18 windows ... (cont.)

HI, I have this weather stripping in 11 windows. It goes into a groove in the rear facing piece that catches the front of the window as it's closed. Not sure how to install it. Also, the measurement in both directions is a hair more than 1/4". Therefore, I am thinking it's 9/32" x 9/32". PLease take ... (cont.)