Viewing all customer Discussions for:

58-105 Gray Pile Weatherstrip, 9/32" x 11/32"

Looking for (1) replacement rollers, (2) bottom U-shaped weatherstipr that goes in that lower notch with the rollers (49" long), and (3) the weatherstrip that goes to the outside at the bottom (img_1780). That outside weatherstip is roughly 3/4" tall and there is a 3/8" horizontal part that was scr ... (cont.)

Good morning, Ive uploaded 3 photos. We need some weather stripping about 1/4 inch wide. I just need help identifying the proper one. Ty.

Replacement weather stripping needed for commecial style door.

I have a 1962 built home with original sliding aluminum windows. I need to replace the weather stripping as the old weather stripping is shot (I don't think it has been replaced since 1962) and a lot of air seeps in around the window thru the gaps. The weather stripping runs around the frame of the ... (cont.)

Andersen Weather seal for bottom front of slider and hard spline for Andersen storm door screen that needs to be replaced.

1980's Circa Milgard Aluminum Sliding Door Both Piles Are 7mm in width Pile 1 is approxmately 7mm High (Slidiing Door Vertical) Pile 2 is approximately 9mm High (Sliding Door Rail Horizontal)

I have a few feet of the original (unused) weatherstripping. It has a 0.250" tall pile and base. The well used stuff in the windows is 0.225" tall, but it's spread out from use. The attached image IMG_0614 is of the virgin stripping. The other two are of the well used stripping. The width of th ... (cont.)

Need felt 3/8" thick 50'

The door "brand" says Oldcastle Building Envelop" The current weather seal pile seems to be a two strip arrangement held behind a removable plate. The brush pile has worn out and the gap is now wide. So far I have not removed that plate. Looking for any input on what product might directly, or with ... (cont.)

The seal is 1/2" wide by 1/4" deep and there is about a 1/4" to seal between the doors. The seal is 7' long. I can't find any name or model on the doors and can't find anyone that remembers who installed them. Let me know if you need more info. Need one strip.

NEED the RIGHT PIVOT SET. The one I have looks similar to a pivot set from US Aluminum, your Product Code: 79-097, but I am not sure. The door swings to the inside of the building and when you are facing it the handle is on the left and the two pivot hinges are on the right. PIC's 2059 and 2062 show ... (cont.)

The weather stripping slides into the slot on plastic piece. Picture shows side with weather stripping top of door is with out.cant find right size. Plastic piece of weather stripping that slides into holderis either 9/32 or 5/16 I think. Fuzzy part is like 2 pieces with plastic in between. Are the ... (cont.)

im looking for some pile weather sripping looks to be 3/8th" tall

9/32 x 9/32

Hello, I've messaged you before regarding some of these parts, but I'm still looking and have some more info. The first pictures are a channel piece we had trouble identifying. I recently noticed that they have the number 0132 moulded inside. I found a local supplier but he was charging more than ... (cont.)

Hello, I'm looking to replace my weather seals. They look like they measure at 1/4 inch wide across the base. I was thinking 3/16 would work.

I want to replace some weatherstripping on the sliding doors, do these pictures help you determine what I need? Thanks.

I need to replace the door pivot hinge please let me know what is the part #, also i need weather strip Thanks

I have four pairs of Alcan sliding glass doors that need the white weatherstrip that seals the edge of the door on the outside and inside when closed. Attached is a cross section photo. The width of the "T" is approx 5/16 inch wide and the bulb itself is about 5/16 in diameter. You can see in the ph ... (cont.)

Greetings, I was asked to send pictures and dimensions for a weather stripping I'm looking for. So here you go. Dimensions are as follows, the strip on the bottom is .27" wide and the total height is approx. .335"