Viewing all customer Discussions for:

58-105 Gray Pile Weatherstrip, 9/32" x 11/32"

I have two 6'8"h x 8'0"w sliding doors with sun and weather-degraded weatherstripping. I've attached a diagram of the track the weatherstripping is installed in. I would say the dimensions for the overall slot depth of 0.08" and the opening width of 0.175" are accurate. The bottom slot width of 0.2 ... (cont.)

Hello, I have a sliding door (SDG-R30-96X96) and the strip that runs from top to bottom on the outside of the slider located just in front of the handle need replaced. Can you give me a part number to order a new one? Thanks, Mark

I purchased from you part number 58-050 which is a Gray Wool Pile 7/16 x 7/16 weather strip. The wool pile is perfect, but the plastice backing is to wide and when researching your site I could not find something that I felt would work. Can you help please? Tks Leroy

I have an aluminum frame door that is missing the pile weather stripping. It looks to me that I can slide a new strip in the channel. It is a 1/4 wide but the inside is maybe an 1/8 bigger on either side. It probably needs to be 1/8 tall

Appreciate your help in identifying this wool pile weatherstripping. 1. Width reads a little over 1/4"W; order 9/32"W? 2. Height reads a little over 1/4"H; order 1/4"H or is 9/32"H available? 3. Will the optional center fin seal work as a better replacement? Thanks, Don

Hello, I need replacement for the attached. It is 9/32" wide and as much as 9/32 tall. Thank you.

I had ordered weather seal then later returned it. I need a solution for this gap. The only problem with the ones that you recommended, 58-050 and 58-161 is that the track size I need is 5/16. So I do not want to order something that won

I have been scouring the internet looking for this door weather stripping. I have it on several of my commercial aluminum frame glass swing doors. All were put in in the early eighties. The pile backing is 5/32" or .150 and the pile height needs to be 5/16". Can you get this size or point me in ... (cont.)

Do you have this product (your Item 58-105) with a 3/8ths or 13/32nds inch gray wool pile? If so, please provide ID number. Ken

1473 Amherst | Weatherstripping questions and product Identification

Hi, Can you help me get the correct parts to seal my sliding door? A few years ago I pulled "something" out from underneath the door and now it lets the cold air in. The glass has Corado or Caradco on it. Thanks!

I have some Traco sliding windows and need some felt weatherstripping. The plastic base is 1/4 inches and the pile is 7/16. Hope this is enough info for you.

I'm dealing with the subject door. I need: (1) Weatherstripped Faceplate - 1 1/8" x 7 1/4" Beveled-Brush Aluminum-I have a part number but am uncertain if it is the correct one. (30') Weathertripping (Wool pile). The existing weatherstripping measures 11/32" x 11/32". (2) Door Sweeps (W ... (cont.)

We are using the 58-134 for replacement gaskets. Can you provide a product code for similar gaskets that are 10% and 20% smaller? I'm hoping to find a similar gasket with the same 9/32" base but a smaller bulb. Let me know if that's possible.

I'm replacing weatherstripping on my 35+ year-old aluminum windows. The track in which the window rides appears to be 1 1/32" wide (maybe 1 1/16" in some places) and the windows themselves are 7/8" wide. The windows take pile weatherstripping in 9/32" channels on both the inside and outside. 1. W ... (cont.)

They are double entry doors, I measured at 1/4 x 1/4 do you carry something like this?

Do you carry weatherstrip like this? Our house is a modular, built in 2009, the door is aluminum. The opening of the metal strip is about 1/4". I don't need the metal part, just the rubber weatherstrip. Thank you very much.

I have a commercial double front door that has lost pieces of its wool pile weatherstripping. The bottom sweep is also in bad shape. I'm having trouble finding the right measurements for this particular sized pile. The door is leaking air like crazy and we are in Florida so you can imagine that t ... (cont.)

I believe it to be 1/4 x 1/4 stripping for the door..... I only saw a stick on option so I figured maybe y'all could point me in the right direction....

How do I keep my tilting window weatherstripping from sliding out of place...its replacement wool pile I bought here that is an exact match...can I glue it in place?