Viewing all customer Discussions for:

70-009 5 Pack, Screen Plunger Pin Latches, 5/32"

Dimensions 1 and 7/16 long pin diameter 1/8 end of pin width 5/16 Please Call me with any other info needed. Thanks, Dave

Hi, the old coil springs are pretty well rusted away and the plastic push caps are disintagrating. Can you match these up please? I would like about 60 pieces. Best regards Bruce

I can't think of another name for this item except to say it is spring loaded inside the frame and is a pull pin. The thing comes from an old Pella screen for a convertible storm door.

Will these work with Pella window screens? 5 Pack, Snap-On Plunger Pin Assemblies Product Code: 70-219

the attached photo shows the screen for my windows . I need to replace some lost push plunger . Could you advise if you sell such a replacement Bill

I believe the Product Code I need is 70-009. Please see the pics attached and advise me what to purchase. Thank you.

My screens are 15 years old and I am looking for replacement plunger pins for these screens. Enclosed you will find a picture of the part.

Hi- I have Hurd window screens and need to replace the screen pins. I see you have model 70-009. Do you know if they will work as a same fit replacement pin. My pin is 1 1/2 Long but diam is 4/32(1/4"). They look close but wondering if the diam will be an issue or not.... Thank you, Leon ... (cont.)

Frame 3/8" X 3/4" Plunger pin clear 1 5/8" I need replacements Thanks

Does the 70-009 plunger pin fit a 3/4"x5/16" screen channel? Do you need a special bit to drill the hole?

Looking for 5/32 by 1"3/4" plunger pins that are double sprung (two springs) for screen frames. About 1,000+ thanks

I'm looking for a lunge pin that is all aluminum, do you have any. The plastic cap on the regular ones becomes brittle quickly and cracks and breaks off. Thank You Cindy

I have several Marvin screens that need push pin replacements. They are from a 1991 install. Can you help?

I need a plunger pin for the screen of a standard Pella vinyl double hung window from Lowes. Do you happen to know if the 5/32 or 7/32 would work better?

Hi, please see the attached photo. I need additional plastic window plunger pin retainers for my Marvin windows as shown. I have the correct window screens, but I am just missing the little plastic retainers that need to be pushed into the actual window frame. This way, the plunger pins on my existi ... (cont.)

Need replacement screen pins for 25 year old Marvin window screens. OEM pin 1 1/2" long made of clear plastic. 3/4" screen frame. The outside original hole dia. in my Marvin screen frames measures 5/32" & inside hole measures 1/8", which fits the OEM pins. Do you have a pin that fits these OEM hol ... (cont.)

My window screens are setup with the 4 plastic tabs that are always breaking. How can I retrofit this top tension and possibly a leaf spring into the frame of the screen ? I was thinking a drill and a rivet set might be easiest but was curious as to what you would recommend. Many thanks ! ... (cont.)

I need replace broken plastic window screen retaining pins. They are L shaped, the pin is approximately 1.25 - 1.5 inches long. The L makes a "lever" that helps to remove the pin when the screen needs to come out.

Hi, I'm not sure if there are different sized screen pins, but IMG_0604.jpg shows what i neeed installed in my screen. The frame width is 3/4" and the business end of the pin goes into the window frame slot which is 3/16" wide (IMG_0606.jpg). I prefer the metal colored pins - which part should I get ... (cont.)

Please help me choose correct screen pin replacement. Photo is of exsisting pin. It is spring loaded, 1.5 inches long. I do not know how to measure the diameter. Thank you.