Viewing all customer Discussions for:

81-030 Acorn Patio Sliding Glass Door Roller, 1-1/4"

I have a Alside not sure what model it is, but i believe it is a 5100 or 6100 series sliding door i just had installed. the problem was the previous Homeowner had lost all of the installation hardware.... like the rollers for the door, as well as all of the Handle/Latch assembly.. the installer call ... (cont.)

I have a Acorn/Doorwal door that needs the rollers replaced and can't seem to locate them. Can you give me all your part numbers that are applicable?

Its 11/16 wide the gold part of the body is 3 inches long , and the wheels are 1 1/4 diameter . Its about 2 and half inches from the end to where the pivot point is for the wheels on the gold part There is a self tapping screw that holds this to the sash Thank you Jeff

We cannot get the sliding Dorwal 1200 door out because of inside tile higher than the bottom slide bar; how does one remove the stable door so that we can then remove the sliding door towards the outside rather than the inside of the house. Thanks. (I recently bought several new rollers 81-030 for y ... (cont.)

Hi, I need some help identifying this part. No markings on the assembly unfortunately. The assembly is 3 1/16 long, 1 3/16 tall and 3/4 wide (all approx), with 1 1/4in wheels. Any ideas? Thanks!

Looking for weatherstrip for an old Acorn DorWal series 1200. it is identified on the parts list as #540-25013 fin seal weatherstrip. It is 1/4" wide at the base and the pile height is 3/16". I need 100' any color. Thank you for any help you can provide

I am trying to replace a roller for a manix sliding window. The roller assemble seems to have the same dimensions as the Acorn Sliding door tandem roller assembly 81-030, with the exception of the 3/4" thickness. The one took from an existing window has a 1/2" thickness. will the 81-030 work? Do ... (cont.)

I have glass sliding door and rollers are bad I did open and remove old rolles it two rolles and on glass i see written Guardian Ans 297.1-1984 sgcc 933 1/8u 16cfr120111 can/cg58 12.1-m so which rollers will be right please advice

Thanks for contacting us! Are you sure you have a Pella brand door? I do not believe that the 81-030 Acorn Patio Sliding Glass Door Roller can be used for Pella doors. Could I perhaps see a few pictures of your existing roller? Make sure that it's fully removed from the door before you take the pict ... (cont.)

I recently bought a 5 year old condo. Sliding glass door does not slide well. Tried adjusting rollers but nothing worked. I didn't even appear the rollers were raising or lowering the door when I "adjusted" it with screw driver. I do not know if the door ever worked well. I can not find a manu ... (cont.)

I ordered two sets of double rollers that I thought were the right ones for my sliding glass door (Item # 81-030). The style is right and wheels are 1 1/4 " but the frame is too tall (1 1/8" and mine is 1"). The length, width, and wheel diamater are all correct, but I just can't find the right one ... (cont.)

Pictures below.

I have three 26-year-old patio doors, I am not sure of the original manufacturer. The rollers appear to be like your 81-030, and were marked as "Delmar Hardware Toronto". The dimensions match with the 81-030, in terms of length (3 1/8), width (3/4) and height (1), and have wheels with an outside ... (cont.)

This is a replacement for an Alside 5100 sliding patio door. All of the measurements match except where your diagram shows 1 1/4" I measure closer to 1 1/8". Wheel diameter is 1 1/8". Is the 81-030 the correct replacement? Thanks!

Hello, I am looking to buy rollers for my acorn door.. but not sure what series I have. The 81-030 is for Acorn Dorwal 1100 Series and 1200 Series doors. Do you have the specs for this door? How high and wide are they? My door is 80 inches high. thanks Marc

You may want to take a look at the 81-138 Patio Glass Door Tandem Roller. It is similar the the 81-030, but it has 1 1/8" wheels.

I have replaced the wheels on my 4'door (8' doorwall) 3 times now. The adjustment screw pushes out on one side only. I have installed nuts inside (even an acorn nut on the inside end of the adjuster) but the 3/4" wide case collapses... the door is very heavy. Do you have a heavy duty model wheel ... (cont.)

I have BetterBilt sliding doors from 1992. Your 81-030 looks right, but what if I'm wrong? Can I return unused product for full refund to my credit card?

The problem is that with the shorter wheel you might not be able to adjust your door up high enough, and with the taller wheel you might not be able to clear the bottom track to reinstall your door. With that being said, do you know the manufacture of the patio door? If it's a vinyl door by American ... (cont.)

Looking at your wheel replacements without the housing. How would this work. right know we have been grinding off the old wheels and using a screw along with a thing blot to attach the wheel. Home depots replacement wheel kit. So with your wheel and axel would we grind off the wheel like normal a ... (cont.)