Viewing all customer Discussions for:

81-036 Peachtree Sliding Patio Door Roller

HelloThe adjustment screw head is damaged and the screw seems to be rusted shut anyway and won't move. So I figured it'll be easier to change the roller.I could not find this model anywhere. I am hoping the pictures can help you help me identify what I need to replace it with.The model I have looks ... (cont.)

Don't have any numbers, probably 30+ years old

I believe the sliding glass door is a Peachtree. 1969-1995?I ordered 81-036 bottom rollers for it from you, had to be slightly modified. But work great. These nylon rollers guide or keep door centered at top.

Need 2 rollers and two of the upper guides To fit PPG herculite K ANSI 7-97. 1-1972 DS -1. OS SGCC - 58 h37

Would you have anything similar to this 1 1/4" steel wheel with a housing. It is used on a aluminum sliding glass door with single pane glass. Thank you.

Hello, I am having difficulty finding a replacement roller for my sliding glass door. Steel B B preferred but nylon wheel also ok. Thanks for your help

7/8 " wide in to rail 1-1/2" tall into rail5/8 tapered stick out of rail when insertertedDefinitely aluminum extruded type - I think :-)Early 70s - Possible Peachtree Door modelAny help Need em today

I am need of a set of rollers for a sliding glass door (pictured above). Would you have this available and if so what would be your price?

Hi Folks,Here are photos of rollers I'm trying to match for three Peachtree sliding glass doors. The part has been cleaned up for clarification and is sitting on a sketch that has most of the dimensions. No markings or numbers can be seen anywhere.I will need 6 pcs.Jerry

This part is to a sliding glass door. I'm remodeling a house built in 1964. I believe this door is original to the house. There are 2 of these assemblies. The panel that they go under is a 4 foot panel. There is not a brand name on the door.

The roller is 1 1/4 diameter. The piece with the screws is 2 1/16 x 1 7/16 and 7/8 thick at the area where the screw holes are. The piece with the roller is 1 3/16 x 1 1/16(the part of it that extends beyond the other part)

I don't see any markings or label on part or on the door

ordered 81-112 was not correct it appears 81-036, may be the correct one will be trying to return the others.

I have three Peachtree Citation Sliding Doors. Two are standard sliding door width, and one is a large slider. When I pull the doors off the track and inspect the rollers it seems the rollers are not framed the same way as your Citation rollers and are about 9/16 wide, The screw to adjust enters ... (cont.)

Hi. Please pull this order 708579 to view the picture of your Peachtree Sliding Glass Door Roller, 81-071. The pivot point is in the OPPOSITE location than I need. Do you have the exact same roller with the EXACT same measurements with pivot point in the opposite location?? *Here is the pictur ... (cont.)

Unfortunately, I didn't watch the how to 'remove' video beforehand. I separated the bottom door frame enough to rotate the floating wheel assembly outside the door frame. The wheel is 1.25" in diameter. The doors were installed in Atlanta, GA in 1971. I'm guessing good chance they could be "Peac ... (cont.)

Hi, I have a peachtree citadel slider, for which I'd like to replace the rollers. The house was built in 1992, so I'm guessing that's the vintage. One roller at either end, with the adjustment screw accessible from the side, on the outside of the door. We also have a wobble at the top of th ... (cont.)

Hi, The older looking one in the pictures is what I need. The newer one, 81-071, is what I ordered from you but it is the wrong one, doesn't work. I can take the door back down and get measurements, if necessary. Let me know if you recoginize what I have and the required replacement. ... (cont.)