Viewing all customer Discussions for:

82-002K Patio Sliding Handle Set with Keyed Lock, 6-5/8"

need replacement for DNS INDSTRIES 13/23 outside pull standard, the pin broke off the tumbler. Inside pull has #16 standard. Door is 1" thick and tumbler overall length is 3/4" and 1/2" thick. can you help?

Good morning,I need help finding the correct replacement hardware for my double sliding glass doors. I see the 82-002K model, but need the other side to close up the opening. See attached photo for reference. You can contact me on my phone Thanks, Bryant

Similar to Product Code: 82-002 ; 82-002K Horizontal bar (in the center of the unit which engages lock) drops and does not stay in place. Is there any way to tighten / adjust tension so that when you push up the bar it stays in place?

I need to replace a patio door inside pull. Stamped as DNS Industries 16 inside pull standard. Patio door locks and unlocks from inside only. Measurements match your 82-008. 7-3/8 X 15/16. Screw centers 6-5/8. But Your latch is facing down and my latch is facing up. Thanks Lydia

I am looking for a lock/latch for a sliding door. 15/16 in x 7 3/8 in

Do you have a replacement part for the piece in the attached pictures?

Please let me know which part # I need to order as replacement

Do you have a product that will lock (from the outside) my sliding glass patio door? The dimensions are: Stile 1 6/8 in Inside door width 1 inch I have not been able to find anything that fits. There is no label on the door so I am unable to determine the manufacturer.

I am looking for a door handle to fit this unknown manufacture door. the sketching on the glass sliding door looks like to be the following: Gaurdian Webster, MaSS ANSI-Z 971-1984 SAFE TEMPERARED LOOKS LIKE SOCO 300 1/8U WMH 3993 18-CFR OR COULD BE OFR -120111 Between the glass there ... (cont.)

Are standard sliding doors Less than 1 1/8 thick? Measuring my door with digital calipers, I get 1.172" thick, just shy of 1 3/16". I picked up a big box store replacement and it barely fit (needed longer screws), key lock doesn't contact, and striker mechanism is so flimsy it bends when lock ... (cont.)

picture of my sliding door key-less lock so you can help me with a keyed one. Phil

Need new hardware to match the following: DNS Industries, 13/23 Outside Pull - Standard DNS Industries, 12 Inside Pull - Standard The locking latch seems to be lower down than the 82-008. Maybe the 82-002 or 82-002K would work... Thank you in advance!

Dear Sir/Madam, I have a boat in England UK on the river.I know the boat came from lake michegan originally.The boat is a BAY HARBOR.i am trying to replace a door lock.On one half it has one half(the latch side,locked from inside the cabin) 12DNS industries miami fla,on the other hal ... (cont.)

trying to replace with an exterior locking handset. Mortise opening is 7-1/8 x3/4. Door depth is 7/8 inch. Lock opening on side is 5/8 x 1-3/8. Does separate purchase handle interfere with key lock?

I want to replace this door handle to be able to place something that can lock this door from the outside. What can I use to replace this door handle

Main locking slide (cast Al presumably) broke. House was built in 1989, original door and lock. Door is 6' wide Aluminum that is 1" thick. Opening in slider is rectangular approximately 7 1/8" L x 3/4" W. Pictures are of lock installed and removed. Dimensions between center of screw to center of scr ... (cont.)

I have a flush mount patio door latch (looks like your 82-008K) on my sliding door on my boat. I need a sturdier locking mechanism with a key. Any options to retrofit with a better locking mechanism? The door can also be lifted out of its track to gain entry since it is on the outer track. ... (cont.)

Hello Swisco Crew! Pete Rose here from Home Hero Handyman Service in Philly. Good friend of the infamous Mr. Paul Pallas. Hoping your team can help me figure out a replacement handle for the above referenced patio slider. Total length top to bottom is about 7.25" LMK if you can help me ... (cont.)

The lock to our sliding glass door is broken and we cannot seem to repair it anymore. Is this one too small for the hole? Please help!

Patent Number 3390557