Viewing all customer Discussions for:

82-002K Patio Sliding Handle Set with Keyed Lock, 6-5/8"

I need a patio door handle the mortise is 71/8" high3/4" wide with a 3/4"x3/4" mortise on edge of door

I want to add keyed entry, and a grab pull bar, to the outside of my patio door. What do I need? The screws are 6-5/8"

This is the original lock on my sliding glass door. It no longer works. Looking for a replacement kit. Am I correct in thinking that the 82-002K door handle set may be the solution? Do I also buy the 82-002 handle separately, or is this included.

Hi, i'm looking for a replacement sliding door handle with lock. i would preferably like the handle on both sides. my slider is really old and the lock plunger is cutout shown in the attached picutres.

I am restoring a 41 year old houseboat that has a sliding glass door. I would like to order all new parts as shown in the reference photos. Please provide part numbers, your assistance is greatly appreciated.

Looking for handle set with outside key entry for existing aluminum sliding glass door. note the handles need to be inset to avoid interference. Internal locks exist that the junction of the sliders. Hope you offer a solution with detailed instructions

Hello,I would appreciate if you could assist locating the correct part. I would like to replace the existing locking mechanism with a lock & key without having to cut into the door frame. I was able to make out a marking on the glass door labelled V861 12GZThank you,Moussa

6 and five eighths inch screw spacing

Hi, please see attached photos of the existing lock. I would appreciate your help identifying the correct part to replace with a lock and key without having cut the door frame. Thanks!

I am trying to determine what replacement part to buy to get a key locked sliding door as the current lock we dont have key for.

There is a number listed on the inside that reads - 1195 1 and 1195 2

This lock needs replacement, looking on your website I think a replacement lock may be lock number 82-002. The handle is still in good shape and can be re-used, will it fit on this lock, if not do you have a complete lock with handle. The color of the existing lock is black. Please advise. Thanks. ... (cont.)

The house was built in 1976 and the sliding door is original equipment. The door is 1" thick and the opening for the handle set is 7-3/16" x 13/16" (+-1/32).The existing set says "Woodbine Ind Ltd Japan" and the installation hole centers measure 6-5/8". It looks a lot like your 82-002 or 82-002K. If ... (cont.)

Need all Hardware associated with this lock for two similar doors. Thank you in advance for any assistance you can be

Hello Parts Dept,I purchased the 82-002K per conversation with customer service rep. a couple of months ago. I ordered it and received it yesterday. order #1100828Here's some questions;1. Figure 3&4 -step 2 I've installed the key ,but what is the pin tumbler?and where do I use the two washers.2. ... (cont.)

From what I could see it looks as if your 82-008 model would work for my door, yes? I would also need a new lock too.

Hi I need to replace a non-key door lock on a sliding glass patio door. 71/2" long & 1" thick frame. Black. I need the lock & catch on the frtame.

Park model slider lock set just pulled out of door with the key. What part do I need?

I have an Alenco 3 panel patio door. Each panel is 34x91. The lock mechanism is the standard one sold ta Lowe?s and Home Depot and it is a touch too small. The screws see to be about 6 5/8? apart. There is a bit of open space at the top of the opening in in the door and the hook, despite trying all ... (cont.)

I have a sliding patio door with this stamped on the door: "acorn series 1200 cgsb 82-GP-2A" The current handle does not even have the capacity to latch, never mind lock, and so, I would like to replace it with a door latch that actually latches and at least, secures the damn thing from the ins ... (cont.)