Viewing all customer Discussions for:

82-218 Mortise Lock, Round Face, 3-11/16"

We broke the handle and can't find a new one to purchase anywhere nearby. It is brass on one side and white on the other (outside) side. There is a picture of it at this link, if that helps. It says swisco.com in the photo credit. Please let us know how we can purchase a replacement. It is a left ha ... (cont.)

Hello: I need a sliding glass door replacement lock, and perhaps I need the lock plus handles kit. There are three bolts to the door handle?the highest and lowest being 4" apart. The metal part affixing was he handle to the door is 7 " long. The door is about 1-1/2" wide. As I was unscrewing the loc ... (cont.)

My latch for sliding door-American Craftsman product.

Please see photos. The lock has a rectangle instead of your square lock. Do you have these available?

I previously ordered a 45° Mortise latch but the slot where the locking latch goes in was too small. The locking latch is shown in IMG 0558.

Do you have this part. This is whats written on the door itself Guardian carleton mich AN81287.1-1884 Safety tempered 8GCC8331/8U 18-CFR-1501II CAN/C028-15.1-M

Need to replace the hook in door no longer locks with the latch. Latch broke and something in door dropped done where latch in door dont come out to lock door

I have been trying to find replacement part for this sliding door. It is an American craftsman slider with blinds. When I tried to take out lock, it fell into the hollow door.

Hello,Your handle looks like our 82-086 but if you only need the thumb latch, you can use our 82-107 latch lever kit. As for your mortise lock, we will need to see a photo of it to identify the correct replacement, which, unfortunately, will require opening the door.

Need help finding a replacement glass patio door latch and handle, house built in the 70s. The side of the latch says W.& F. MFG Inc, Glendale CA.

can you please tell me which keeper I need ? Thank you, Robert

I recently moved into my new home with this exact sliding glass door but no key. I was wondering if i could just purchase this keyed handle set and use the key to unlock my door or will i need to replace my entire set in order for the key to work?

when we unlock our IWC patio door handle, the mechanism that causes the door to be locked "retreats" all the way into the casing (IMG 6624). We have to dig it out with a screwdriver and then we can lock the door. What do we need to buy to replace this mechanism? And, how hard is it for someone who i ... (cont.)

Looking for this part to lock our slider. We have two sliders so this is a picture of the other one. We need to find the part that attaches to the frame

I searched the model # and found a forum on this site of someone with the same information, so I ordered the 82-218 Mortise Lock, Round Face 3-11/16". (Order # 1354721. I need to return this and get assistance ordering the right one if possible please. This one seems to be the same size(roughly a qu ... (cont.)

house was built by US Homes. Original door. I'M a new owner. The lock no longer works.Photo of all sides of the lock and handles attached. Thx for your help Mitch

Hi there...our mortise lock has been dropped down in the door by an older tenant, an were not sure which one to purchase..I have the 82086 handle to put on, as I have the gold handle on one side, and so far all the measurements are the same from old handle to the newer model,other broke off recently ... (cont.)

2260 latch mechanism Sash Controls 2260 Taiwan D340398 Ferndale MIthe latch mechanism seems to have frozen and does not move when levers on handles are moved. I think that this is the part that I need. The handles seem to be fine. Latch mechanism is about 3 and 1/8 in. long and about 1/2 in. ... (cont.)

need to replace mortise locke, outer screws are 3 3/4 inches apart, thanks.

I have a order number 1343995 which included mortise lock. that did not fit my keeper which holds the lock in sliding door. Can you recommend me keeper which will fit this mortise lock.