Viewing all customer Discussions for:

82-218 Mortise Lock, Round Face, 3-11/16"

When the lock lever is moved to the full unlock position, the latch is retained and subsequent movement of the lever will not extend it. But when the lever is moved only far enough to unlock from the striker plate, then the lever will successfully complete the lock procedure by a full downward move ... (cont.)

This is a photo of my door. The broken piece is obvious. Mid-screw to mid-screw is 4". Can I replace only the broken piece, or do I need to buy both the in and out handles? Also, which part should I get? Thanks!

I need your 82-033 handle, but I need to know what mortice goes with this. I was broken into and the inside was broken. It is for a rental property, so I doesn't have the part with me. I am going to try to measure tonight and call you tomorrow. Thanks, Ronnie

Hi Our slider latch somehow got jammed and now will not lock. Do I need to replace the entire handle or can I just replace the insides? I have attached a couple of pictures. The knob that we turn does feel a little jiggly

I have a Pella Sliding Glass Door that need the rollers replaced (one side is bad) and the small knob to lock the door is broken. The house was built in 1982-1983. From your web site, I believe the roller assembly the I need is the 81-098. I have attached pictures of the small knob I need for loc ... (cont.)

I'm attempting to match up my broken mortise lock set to your part number 82-218. Can you provide me the measurements from the locking keyway center line to the back of the mortise lock and then from the locking keyway center line to the bottom of the mortise lock. Mine measures 1/4" and 7/8", res ... (cont.)

I have a patio door with a boken mortise lock. I've taken the door handle apart to see the mortise assy. Viewing your website part no. 82-218 appears to be the best match. (rounded ends) The only markings on the door or latch assy. is on the glass Gaurdian Carleton,Mich. I'm not sure about 45 deg. ... (cont.)

I need two sliding door handle sets which I believe to be 82-033. The mortiss for the lock is 1 inch across and looks to be 3 15-16 high. Do you have code for the 1" wide mortiss that goes with the 82-033? Does the 82-033 come with the lever for the locking mechanism, or do you by separate? ... (cont.)

Have what I suspect is an old HD slider door, +/-10 years old. Looks like about 2" thick, white, handle holes about 4" on center? Which parts do you recommend?

I have a sliding door sgd-r20 96X82 and I have a problem with the door lattch The latch would not lock any more in other words the hook will not engage to the opposite latch hole seems like spring problem please help Amin

Hi, I need to replace a handle and lock for a sliding glass door for a customer and there is no name or model # on the door itself. If I order the parts I think it is, and it is incorrect, can I return the parts for a refund? Thanks, Kayla

Hi, I have a Philips Products series 870 Sliding Glass Door. The internal lock os broken. Would you have a replacement lock? Regards, Randy

Thanks for posting! As you can see in the Related Item(s) category on the 82-035's product page, there are a few options for mortise locks. Take a look at our 82-214, 82-218, and finally our 82-226, and then compare these to your existing mortise lock. Do any of these match your current hardware? Le ... (cont.)

I have four broken sliding door handles with 3 5/16 distance between bolts. Two Right Handed Handles (Brown) Two Left Handed Handles (Brown) They resemble 82-005 but the distance is 3 15/16 and not 4 15/16. I need one with keyed exterior handle. The three other exterior handles don ... (cont.)

my sliding door looks form out side with the key, but when try to lock form inside using turning lever, it doesn't lock some time. every time we pull down to lock, it release back. after couple of attempt it locks but if we try to roll around the door side ways it unlock. do you think that is it tur ... (cont.)

I have your replacement handle, but the lock fell down (when I took the old handle off) - ? How do I install the new lock and handle (Ok, the handle is not hard to install once I put that inside lock where it belongs) HELP! thank you

We are looking for these replacements for a customer. THe lock measures 4" between screws top to bottom. 3 3/4 midpoint. We need the handle, the lock and the latch on the door side.

Hello, I have a sliding door handle that I need to replace. The lock piece that is in the middle dropped into the bottom of the door. From the sticker it looks like the door has a model number of SDG-R15 or SDG-R20. I'm attaching the pictures. Thanks. Andrew

Sebastian on phone suggested sending photo of lock: latch is stuck inside and spring has separated. please advise on way to repair or if part has to be replaced, how to obtain. thanks!

What is the trick to not dropping the lock in the door frame during installation?