Viewing all customer Discussions for:

84-073 1" x 13/32" Acorn Door Corner Roller Assembly, 1" Wheel

I'm looking for the plastic bracket above that the screw screws intot to keep corner attached do you know if you have this peice? Thank you like always, Brian

Do you have this roller? I didn't see it. I see a similar one, but none with grove on metal piece.

As you can see, I bent it, from hitting it with a hammer, removing it from the frame. The only marking that I could find was up in the top sliding door frame. The outer measurement is 1" The bottom flange is 7/16" The top flange is 3/8"

The rollers are shot on this screen door. I can't figure out how to remove the rollers. There are no mounting screws, only the roller adjusting screw. There is a square head screw on each corner of the frame, but I think that is what is holding the frame together. Does the frame need to be disas ... (cont.)

Hi. I've tried getting these rolllers out with a philips screwdriver like your videos show. It seems like they are attached and maybe I have to replace the whole corner? Thanks for your help

I ordered 95-020 as a replacement for the screen corners. They looked they would work, but widths weren't listed. Unfortunately they are too wide. Do you sell narrower width corners. I have attached a picture of the old broken parts on the left with measurement. The 95-020 is on the right. Thank you ... (cont.)

This is from an Acorn Dor-wall circa 1980. The code between the insulated glass is L C. I'm looking to get 4 rollers to replace at the top and bottom of the screen. Thanks, Mike

last year I bought 2 acorn door rollers from swissco item 81-030. These have 2 roller wheels each. My doors only use 1 roller wheel. Do you have the right roller for my doors.

I'm working on a project which included re-screening 3 sliding patio doors. One of the doors(4'x8') fell apart as I took the screen off. I salvaged 2 pieces (pictured). I can't seem to find this exact size anywhere. I'm hoping you can help. Each leg of the corner is 3" long X 1" wide X 3/8" thick ... (cont.)

I encountered a slider patio door which is missing both rollers. I found this plastic piece located where the rollers should be (see photo). I believe the plastic piece may be roller housing but the metal roller part is missing from the center. The roller itself would be concave The hom ... (cont.)

Morning, I recently ordered your # 84-137 roller assemblies. turns out these are to large. I need a 3/8 thickness instead of a 7/16. Do I need the 84-011? Please advise when you can.There are no numbers on the old rollers Thank You Darryl

dissimilar metal corners in Acorn patio sliders in a saltwater environment corrode due to electrolysis. Looking for all nylon corners and all nylon roller assembly as a fix. Do such parts exist? Any metal even stainless in contact with the aluminum frame will fail eventually. Suggestions?? ... (cont.)

Would you carry roller assemblies 1" wide, 3 3/8" long, 13/32" thick with a 15/16" OD plastic roller. Thank you.

I was wondering if you had a frame corner that would work with my 1984 Atrium door screen frame.

I have an Acorn sliding door (1996) on which the screen door corners and rollers are shot. Your part number Product Code: 84-026 is the correct dimensions, except the wheel size. Yours is 15/16". My original equipment is 1-1/4". I realize that the smaller wheel will still work. I just wondered if yo ... (cont.)

Attached is a picture of our screen door roller. The roller wheel itself is riveted to the frame. There are no marks on the roller. The screen door handle has "PGT" with the number 1805 on it.

It is the same measurement 1" x 13/32" Acorn Door Corner Roller Assembly, 1" Wheel however there are so many do i have the right one?

I need a replacement for part # 8221 ASP It looks just like your part 84-026 but it is only 1" wide instead of 1-1/8" wide. I tried the 1-1/8" ones and they did not work.

Need to replace part pictured above

It looks like either a 84-011 or 84-073. Any assistance would be appreciated. Need 4 to 8 pieces. Bob