Viewing all customer Discussions for:

89-003 Patio Door Lock Keeper, 3/4" Wide

the keeper measures 11/16 inches wide and 2 5/8 inches long. The door is on a townhouse we just bought and it was supposed to be fixed but we overlooked it in the walk thru, so i am fixing it myself. I took a picture of the door to show the hook that engages the keeper. thanks.

I have an Alenco 3 panel patio door. Each panel is 34x91. The lock mechanism is the standard one sold ta Lowe?s and Home Depot and it is a touch too small. The screws see to be about 6 5/8? apart. There is a bit of open space at the top of the opening in in the door and the hook, despite trying all ... (cont.)

I was looking for a Marvin Screen Stop and sill strike. Part # 05700030 or 05700029. The handle is a Ultimate Screen Handle or a Marvin sliding screen door. The handle is okay, I just need the locking latch.

Need two new recessed patio door handles and hopefully new wheels. This home is in Laughlin NV and was built in the 80?s

The 82-002 lock set shows that it comes with a lock keeper. Is this the 1/2 inch wide keeper or the 3/4 inch wide one?

hi my patio screen door connects to this latch, do you know the item number? thanks

I need to replace a patio door inside pull. Stamped as DNS Industries 16 inside pull standard. Patio door locks and unlocks from inside only. Measurements match your 82-008. 7-3/8 X 15/16. Screw centers 6-5/8. But Your latch is facing down and my latch is facing up. Thanks Lydia

Screw to screw is 6 5/8 inches as close as I can tell, Also, I have other doors with same latch assembly that I need to have replacement handles with brackets. Thank you.

I think I have this lock at my sliding door (see pictures) and its not working now. Actually the grapping hook is not working. (1) Is there any other lock for the same opening with stronger grapping arrangement? I don't need the lock but want stronger grapping?

I could not find any markings and I can't explain it very well. The broken piece in the photo attaches to the inner frame (where the door closes). The lick mechanism is still intact inside the door. I have three doors with locks and their design is a pain the neck. Any suggestions? ... (cont.)

Installed in 1984. The latch parts on the left and right doors were removed in order to install a dog door panel. Then they were lost.

I need to know which latch replacement part I can order to work with my door.

DNS Industries, Miami, FL Chrome, hole centerlines = 6-1/2", keyhole centerline from top of exterior plate is 4-1/2". Inside lock handle has 12 INSIDE PULL JAPAN. Also has a raised numeral 2about 3-5/8" from the bottom The inside door pull has a 'Cherry' color wood handle (1-1/8"x9"x7/16") mount ... (cont.)

I am looking for a replacement lock/pull for my sliding door. Markings on the existing parts follows: DNS INDUSTRIES.11 OUTSIDE PULL MIAMI FLA. -1400 SERIES DNS INDUSTRIES.12 INSIDE PULL MIAMI FLA. -1400 SERIES Please advise if these are available. Thank you. Mike W.

I looked through your website but was unable to find my hardware from the pictures. My patio door is about 20 years old. The opening in the metal door is 1" x 7.25". The opening is cut through both sides of the door and is located 5/8" from the edge of the door. I have attached several picture ... (cont.)

DNS INDUSTRIES 13/23 OUTSIDE PULL, -1400 SERIES AND 01 INSIDE PULL

The screws on handle measure 6 5/8" and were attached to the external keyed handle with black plastic mounts. the handle opening on the door is 7 1/4" high by 3/4" wide with the lock opening pretty low and 2" center hole. Notice the exterior handle, it sat on the outside of the opening edges and set ... (cont.)

This is for a 40 year old slider door. The current lock is missing the bar to latch onto. The distance from the mounting bolts is 6 5/8 inches. I need a replacement for the lock, handle and latch.

I have identified the main lock as your part #82-002, Sliding Door Handle Set, 6-5/8" However, this part does not come with the other part, installed in the accompanying door, which grabs the pin (or teeth) coming from part 82-002 and locks both doors together. The doors were installed in 1992. ... (cont.)

The locking part of this handle has been missing since I bought the house. Can't find a new one. Not many numbers on the door or handle the only part number I see is the sgd-30 on the gold sticker. Any help will be appreciated