Viewing all customer Discussions for:

S351-25 25" Series 351 Channel Balance

Looking for a replace per the photos. Non tilt window. Rod is 25 inches long, about 1/2 in width. Says 24 4 AO Caldwell on the rod. Thanks!

Metal length 25", inside depth 1/2", channel width 1/2".Spring length end to end 12 7/8".Window frame clip 7/8".Plastic end (clip end) 1" tall.Plastic end (clip end) 1 3/16" long.Plastic end (none clip end) 1 1/4" not including small extensions inside channel."If you prefer I can ship you a channel ... (cont.)

Hi, attached are pictures of my window channel balance, balance clip, balance shoe and balance top. Please help me in identifying it so it can be replaced. If possible, please send me a quote for 8 complete channel balances. Thank you for your time and help. Looking forward to hearing from you. Me ... (cont.)

Hi - see attached photos. Appears to be a Caldwell with marking 24 4 JK CALDWELL It is 1/2" width (per your instructions) Metal portion length is 24 and 7/8ths inches Neither plastic end has a wing (you'll probably notice one is cracked) Can you recommend the right replacement? Thanks! ... (cont.)

I'm looking for window channel balances. They are 25" in length (Just the metal channel portion) The part # listed on the balance is 24S088081-31F. I do not have the sash weight at this time but was hoping the information provided would help

I believe these are 25 inch channel balances with a rating of 2430 but I just am not sure of the series

Hi if you need better pix let me know. Do you have this balancer ? If yes what's the price ? Thank you Rommel

Request review and ordering information; I did one of these, on a different window, earlier this year, it was a 25" Series 351, looks the same, but I'd like confirmation before I place my order... Thank You.

Unfortunately both springs came loose from window. There is a part number on the channel section, 2430Y

I need 10 of the 29 inchers I need 4 of the 25 inchers

Stamped with part no 2430Al channel is 25" long. Hook is broken off the end of the spring. Need entire assembly or just the spring?And I have another pair stamped 1620 with an AL channel length of 17". This is the 1620 but they look the same.

The first three pictures are 25" x 1/2 (2440) , the last two are 17" x 1/2" (1630). Before purchasing I saw several that looked alike and I want to make sure its the right ones before purchasing .

Hello, I need to replace 3 sets of window balances. On one of the balances the stamp is 24 - 3 CR Caldwell. On the other one it is difficult to read but appears to read 15 - 2 LP. When I measure each with a measuring tape. Excluding the plastic ends the 24-3 CR measures 25 inches. The 15 - 2 LP ... (cont.)

HELLO, I AM LOOKING FOR [3] OF THESE CHANNEL BALANCES W/ ASSOCIATED HARDWARE[PLASTIC ENDS]. THANK YOU.

They measure 25' metal to metal.The only stamp is 2420.Do you think i need one for each side? 2 windows are involved. Thanks

need help with parthello dave long time no c

Hello. Trying to figure out which balance to order. This is a 25" balance. Thanks. Jason

26" x 1/2 number on balancer is 2440 d or r. Can you provide replacement part number so I can order. Thanks.

Hello, I'd like to buy the parts to replace my bad balance rods, but I cannot identify the guides. Could you assist me? The rods are 25" long, 9/16 wide and 5/8 deep. Thank you!

house built in 1991. 1/2" wide, 25" long, 2440.J stamped on channel. Thanks, Wayne.