Viewing all customer Discussions for:

S380-27 27" Series 380 Channel Balance

We have several windows, actually all of them that need replacement ballasts. All windows are the same size and should have same springs. I will verify once we get a part number. Thank you for the help.

Numbers on my channel balance are 26-3 kx cmc 11 The metal part of channel balance measures 27inches. I need 2 replacement parts. I will also need 4 new takeout clips to go with these parts.

Hello,I recently ordered some sash guides 18-171 Stepped Sash Guide, Alpine. They fit my current balances and matched my old ones perfectly. Unfortunately, they didn't fix the problem of the balances shooting up out of place. We have a manufactured home built in 2005. The balances look ok, but they ... (cont.)

Hi. I need replacement block and tackle channel window balances for my side load sash, single hung window. The string broke so I think it makes sense to replace the entire channel balance instead of replacing some of the internal parts. Hopefully you can tell from my images, but what part do I need? ... (cont.)

Need a channel balance stamped 26050 FU CMC 2 for a Millguard single hung open up no tilt.

Also need clips for it as well as locking latch. Vanilla windows

I'm looking to buy 4 of you 380 products but not sure what weight stamp to buy. Can you help with that option. 27" length, 1/2 width and 1" base guide

I would like to find the correct window channel balance to replace my current one which is broken. The stamp on the non-tilting window balance says "26 4 GU CMC 2". Do you have the correct replacement part for the entire mechanism? Thanks.

I'm trying to find and order replacement parts for my window. The balance spring broke

Printed on back is Caldwell 26 9 Metal part measures 27" one spring unit is missing. Clip is broken on the only unit that fits. Unsure of the make of the window but small removable cap looks like M W

Hello,I am the 3rd owner of a manufactured home built in 2006. I have a set of arched-top and non-tilt windows made by Kinro that I want to replace the channel balances. The left window raises very easily, but takes a lot of effort to close. I weigh close to 200 lbs. and it takes most of my weight t ... (cont.)

I am looking to replace the balances for a Milgard window. It is 27 inches long and is marked at 26 4 HN Caldwell. There are wings on both nylon end pieces. I have attached photos. Please let me know if you are able to replace these (I would like two, even though only one is broken as the "good one ... (cont.)

Kinro windows for a (RV) park model 371 purchased in 2019. I measured 9/16 width and 27" length. Windows are heavy. Sash weight model needed is requested. I need : 6 no-tilt window channel balances 2 take out clipsAndrea

Dear Sir/Madam, I need replacement for window balance which has marking of 26 4 IW CMC 11 but I measured the length is actually 27 inch and bottom fitting is 1 inch. Please suggest if the 27" Series 380 Channel Balance (Product Code: S380-27) will be right replacement. I need 4 of them. Thanks and ... (cont.)

I need 2 load balancers with plastic ends and inner workings. Basically I need a full complete replacement. It's about 27 inches long. Also need the take out metal clips located above corners that hold the load balance in its place.

Please help with this part number, and let me know if you need other pics, or more information. Bedroom windows27" x 9/16", 25 lbscode = 26 4 GN CaldwellThank you

Hello! I'm looking for a handful of replacement balancers for my windows. The length of the balancer minus the end fittings is 27" and the etched numbers read 26-3 KC5 CMC 54. Let me know if you need additional info. Thanks!

The length of the channel is 27" inches and the width is 1/2". The only markings I found say: 26 4 IV CMC 9. Please help me. Thank you so much!

I am looking for a replacement part for the channel balance of my slide-up window. Please help me to identify this part. I included pictures of both ends (one plastic part may be broken, not really sure), and the hook. The length is 27 inches. The marking number is 26-4 AN5 CMC 8. Please let me know ... (cont.)

HelloPls help identify my Caldwell balance type with the pictures i have attached, so I can purchase replacements for my windows. The balance is 27" in length. If you can send me links and part# to the exact balance part I have to purchase, that would be great. Additionally do i need to install this ... (cont.)