Viewing all customer Discussions for:

21-005 Bifold Door Pin

Please help identify.

Are you able to ID the pictured pivot pin? I have an old Sexauer part number if this helps for reference of 296210. Thank you for any help you can provide.

Can you please provide a list of replacement parts to renew these U.S. Plywood Bi-Fold doors? Thanks!

Do you have this? Need spring and top and botton caps

Hello, I got these grommets (21-163) for my bi-fold doors, but they don't seem to fit the guide pin. Is there a bigger size available? Thanks in advance!

I need replacement bifold door pin caps, and the post is .3 or 3/10 of an inch. These have just worn out or fallen off over time. Can you help?

hello I am in need for pins for a complete bi-fold door and pivot clamps for them The upper pins I have are the same as 21-065. do you think that the pivot clams 21-154 will work for me

I need to replace pin caps on several bifold doors. The measurements are shown in the photo but are as follows: Pin 5/16" OD Pin length 5 1/4 inch Pin cap hub 3/8" OD Pin cap flange 1/2" OD Thank you!

Built in 1970

LOOKING FOR NYLON CAPS FOR THE TOP AND BOTTOM LEAD ENDS OF STEEL BIFOLD DOORS. THESE DOORS WERE PROBABLY INSTALLED IN 1974. THE HINGED SIDE OF THE DOORS SEEMS TO HAVE A LARGER SIZED PINS. I WOULD APPRECIATE HELP LOCATING NYLON (CAPS) FOR THE LEAD (CENTER MOST) DOOR PINS WHICH ARE SHOWN IN PHOTOS. ... (cont.)

Need help with these replacement parts for 1970s metal closet bifold doors. I am attaching some pictures. I have pins, but need caps, springs, and whatever holds the pin in place. Can you help me?

For Ternes steel bifold doors made approx. 1972. Also need replacement knobs

The bottom guide of this metal, louvered door needs a new guide that has a nylon tip, it's worn off completely. I cannot find any labels that have the name of the manufacturer, but they were located in Roseville, Michigan. The doors are very old. I'm the second or third owner. Also I'm somewhat hand ... (cont.)

We're looking for pin caps for Evans Products Company bi-fold doors model B. Total height is 0.42", outer diameter is 0.37", and the rod is 0.30" diameter. The bottom flange on the cap is just under 1/2" in diameter.Do you have a model that would replace that? Please let me know if there are any que ... (cont.)

It appears that your part numbers 21-001, 21-007, and 21-154 could replace the parts in the attached photographs. I assume the guide pins would also fit the upper and lower door tracks. Could you please confirm all of this before I order? Thank you

I have a US Plywood metal bifold door and I need replacement pin caps. The pin is 5/16" in diameter and therefore requires a cap with a 5/16" inner diameter. Do you have any images of the pin without the cap, or the underside of the cap? Is this pin entirely 5/16", or is it a smaller diameter u ... (cont.)

I have two sets of US Plywood branded Metal Folding Doors. Both are obviously reasonably old. The metal and plastic fittings are worn or missing and I would like to buy 4 complete sets of parts, one for each corner, including the 4 moving metal sliders, which sit inside the channel rails, into which ... (cont.)

This is a Top Pin from a Metal bi fold benchmark 7ft door. It is bent but I measure it at 6 & 1/2". Do you have a replacement for this?

Hi, I have metal bi-fold closet doors that use 5/16" diameter guide pins. The caps are all worn and need to be replaced. Attached to this e-mail is a drawing of the guide pin cap. Will you please let me know if you have this cap in stock? Thanks. Marco

I have three sets of doors by US plywood. The pins are 5/16 by 51/4 long. The top pivot pin looks like the Fenestra pin and spring. the bottom slide pin is threaded at the bottom of the pin with the nylon peice measureshole size is 3/16, the ring is 5/8, and the end is 3/8. I am not finding the repl ... (cont.)