Viewing all customer Discussions for:

21-042 Bifold Door Top Pivot and Guide Pin, Benchmark

I am trying to fix some metal bifold closet doors, but the attached pins are missing on a couple of doors I need to fix. Will your hinges replace these okay? They are very similar but slightly different. Here are the parts I see: 21-007, 21-001, 21-065, etc

I believe I need the guide pins on my benchmark doors. The ones that are stationary are good, but the ones that slide on the track have no tension to stay in the track or didn't fully reach the track. I see the parts that I think I need, but how do they install on the door so that they pop into plac ... (cont.)

I have a few sets of bifolding doors that I need lower replacement parts for. The current parts and door photo are included.

Hello, Would you be able to assist me with locating and ordering parts for the referenced doors? I'm looking for the following components to install the Benchmark Steel Bifold Doors. Tracks- (1) 24" & (1) 36" Hardware- all components needed for the doors to swing. Please note, I've added photos o ... (cont.)

Hello,I want to replace all hardware of my metal bi-fold closet doors in my house, and need help to identify what they are. Thank you,Lei

Looking to find this. Joe

Hello! I bought a condo built in 1972 and it has metal bifold doors. I need help identifying the pins from your site that would best replace the old pins currently in the doors. Thank you so much! Audrey

I am renovating my place and decided to spray paint my old closet doors, unfortunately once I removed the doors the top pivots came off and the little plastic plugs are no longer keep them from springing out. I will need to order new top pivots and bottom pivots along with additional stationary pivo ... (cont.)

I am retired woman and will have a handyman do work if parts are still available. The door is 36 inch wide. There are four of these doors in the home. This one is in disrepair. The actual doors are in good shape. I would like to replace all of the other parts. I believe there also should be some typ ... (cont.)

Hello, I'm trying to get all the components for a Leigh Full Vu steel bi-fold door. I looked on your website and came across what looked like the parts put wasn't sure. The one product code I found was 21-108 and at the bottom of that page was what looked like the parts I needed. ... (cont.)

Hello The top corner bolt securing door to track is gone. Can you advise what replacement part is needed. Benchmark sticker of brand above

I have two metal bi fold doors that I need all new hardware for. Do you carry? Benchmark doors.

I have a mirrored Benchmark bi-fold door. The hinges had separated from the frame, fixed that. Trouble opening, hinges part of problem. There are two pin holes, pins were in first, on bottom, second on top. Which hole should I use? Track and pins good shape. I wasn't as smart as I thought I was. Doo ... (cont.)

I am looking for a metal bifold door track. see pictures below

Good morning I need new tracks for bifold doors from the 1970s. the opening is 48 inches. I need the upper and lower track. I hope the pictures help.

Please help identify hardware.Not sure if this is original hardware or not. Need enough hardware to completely re-do two bi-fold doors. Long pieces measure 12

I'm trying to repair 2 Benchmark steel bi-fold doors. One is 3 ft wide by 8 ft tall; the other is 2 ft wide x 8 ft tall. The top pin on the 3 ft door needs replacing (on the leading edge) and the top and bottom pin on the 2 ft door needs replacing (on the leading edge).

I need four outside pivot rods with spring I believe . The inside pivots are in good condition..this is 2 -36" bifolds ... Can u find the correct outside pivots for these doors, they are missing, thank u

I need a replacement part for benchmark bifold steel doors. Pictures show one part intact on one door, but the same part is missing for the other door. Please let me know if you can help me. Thank you.

Well, I finally received pictures of the door to give you an idea of what I need to make repairs. So, this is the bottom of the door(I think) which has the hardware still intact but I need the hardware, the pivot pin/screw and track pin/screw for the top. I'm not sure what the actual names are but t ... (cont.)