Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

I need balance rods for milgard windows which I have put heavy units in the vents. 4 @ 27" where the vent weight is 56 lbs. 4 @ 21" where the vent weight is 33 lbs

have some Kinro windows bad balancers.........pictures attached....is 27 inches long and 1/2 inch wide........appears to match your 385/27 with standard ends for that. No numbers anywhere on the balancer. Sash feels between 20-30lbs...can you identify from attached pictures and information. ... (cont.)

Looking to replace 2 balances marked with 26 4 Jr Caldwell that measure 27 inches.

I think the metal part and two end plastic plugs are in fine condition but the spring and string inside got cut off. What should I buy? Do you guys sell complete assembly for this? Thank you.

Need (6) 32 9 AW CMC 7 Need (2) 26 6 EW CMC 4 See attached Pictures

Hi, This is my second attempt at a post. I need a replacement part for my window channel balance part# 26-4 CA2 CMC 4. It is 27 inch long and 1/2 inch wide. I think I need an S380 or S385, but can't tell the difference from the pictures. I've attached pictures. Thank you for your help, James ... (cont.)

Replacing balances for 6 windows that weight approx. 23 lbs. Current balance ID stamped" 26 5 HS Cauldwell". The balance is 27" long by 1/2" wide. I'm leaning toward the Series 385. The channel balance top is winged (wings broken off in photo). The channel balance shoe is winged too. According ... (cont.)

Hi, I've got a few windows with busted channel balances. The info stamped on all of them is "26 4 HK Caldwell". I'm hoping someone can point me in the right direction! Thanks!

Hello there, Through all the posts I have seen. None have covered the one I have. Several are close, and I would rather be safe than sorry. The ones I have are labeled 26 4 CALDWELL JL. I hope this helps to identify the right part. Thank you so much any and all assistance that may be provided. ... (cont.)

Hi, I need to replace 2 channel balances for a single hung non-tilting vinyl window. The marking on the current balance is "26 4 LS CALDWELL" the window sash weighs 15.2 lbs. The width is 9/16 or 1/2 inch. Each end piece has 2 tabs, one on each side of the plastic tab. The length is 27 inches. ... (cont.)

metal channel (not including plastic tabs) 27in. It is is 26-6 balanace. See pictures for the plastic tabs. Please help me match it. I need 2 complete balance to replace the broken ones. Please quote me 2 pcs. Thank you, Dean

I have narrowed down the balance to the S385 27 inches model. However, the option goes as far 2670 whereas on my old balance the printed index says 2690 29. Can you please help identify the right model from your selections? Thank you.

Hi I am looking for parts for my window I know it needs sash balance also looking for window plastic clips that are on top of the wind down Thank You Gabriel

Hello, I'm trying to replace a broken window mechanism and have no clue what I'm looking for. I know one of the channel balances is missing as well as the take out clip. I have another window right next to it and it is stamped with 26-4 AF5 CMC 61. It measures 27" in length, 9/16" wide at the edge o ... (cont.)

I need to replace a bunch of window channel balances in my house. I have a bunch going bad at this point I am attempting to figure out end pieces as they are all identical and then I can start taking every window apart so I can figure out which ones need to be ordered. The current one I have pictur ... (cont.)

I have a 27" channel balance (2 actually) that have hemmed edges, not straight edges. Other specs below... -15-004 shoe -19-005 top -Printed (not stamped) on the metal: "26 4 BV CMC 2" -Tension adjustment screw near the shoe/base Do you have this exact replacement part? If so, I'd like to ... (cont.)

It looks very similar to your S380 and S385, although mine has a channel on the bottom of the top piece. The stamping on the channel is "26 4 AQ Caldwell" Channel is 27" long, 1/2" wide. The top piece is 1 9/32" tall, shoe is 15/16" wide. Bottom shoe is 1 1/8" tall, shoe is 15/16" wide T ... (cont.)

I am not sure which is the correct channel replacement for a Milgard non-tilt window. I believe I need the

I sent a request last week but I didn't see a response. My email is limited to 4G so maybe it's lost in space. The reference # is D14214. I'll give you the info again: I have a Milgard single hung non-tilt vinyl window with a sash that weighs 33 lbs. the metal portion of the channel balance is ... (cont.)

I Have Milgard window with bad sashes. They are 27 inches long with the marking of 26 5 AU CMC 2. It looks to me they may be the 380 channel series but wanted to know what you think. You have been great help in the past. Thank you, Curt