Viewing all customer Discussions for:

87-193 1/2" Flat Steel Roller with Axle Pin

These are off of approx 58"x58" windows. The sliding half is approximately 30" x 58". There are two bottom rollers with one screw attaching them on each lower corner of sliding window. Windows are from early 1990s.

This is from an old oak 4 drawer cabinet. One is missing and the drawer will not close without a ton of effort. Might you have something like this or a close alternative? Thank you

i need to replace some drawer rollers for the kitchen drawers. these cabinet and drawer units were installed in the early 60's. so far i have found nothing locally and hope you can help, i have included two photos to show what i am looking for. thanks for your time and assistance in this matter. ... (cont.)

this is a brass roller 1/2: in wide

I am looking to replace the brass rollers in my window slides. I already have the plastic window slides but need additional brass rollers. The brass roller measurements are: Diameter = 12mm, Width = 6mm while the pin = 3mm

I need replacement rollers for the window in a new to us house that I do not know the manufacturer of. PFA images of one of the rollers I was able to remove from the frame. The bodies are OK, the brass wheels were not cleaned, got stuck, and have flat spots worn on them. Full replacment or replaceme ... (cont.)

45 year old home with Viking/Temp-Seal Sigma 115 windows marked with 77-2 inside the panes on the aluminum. The rollers are shot in a few of the frames, and I'd like to replace them all. Thank you for the help!

Need 12 pcs. The window is aluminum sliding window I do not have any name or number to give you. Do you have anything that looks like this

Hello, I'm trying to replace these small circular plastic guides that support the side edges of plastic kitchen drawer bins. The drawers glide along top-mounted plastic glides that fit through a notch in the back of the bin that is shaped like an upside-down "T". There are then lips on the sides of ... (cont.)

Good morning. I Have been for replacement part for my folks kitchen drawers from the early sixties. Do carry these ? Thank you

Anything like this available? Sliding windows part of a solarium added to house sometime in past - not sure what date, manufacturer, who installed, etc. All brass rollers have flat spots. Alternatively, the roller is brass 1/2 inch in diameter. Axle is 3/16 in diameter and 3/8 long. Replacing r ... (cont.)

I'm trying to find the replacement wheels for keller aluminum sliding windows, circa 1978. The wheel is steel and is 9/16" diameter and 3/16" wide. The axle is 5/32" diameter and nylon. Also how are these removed and replaced.

Hey there, I'm looking for a sliding window roller very similar to the 87-193 in your catalog. I don't have a photo of the assembly but it's basically the same as the photo of the 87-193. The only difference is the wheel I need is 5/8" in diameter and the axle is 7/32" in diameter. any ideas? ... (cont.)

Hi, After installation how does the axle pin for the 87-193 stay in place? Is it shaped with a locking mechanism. On installation is it forced into the holes of the window's aluminum flange? Thanks.

Many houses in the Reno, NV area have these unbranded aluminum sliding windows. The rollers and/or axles in most of our house are shot. With some effort I could remove them, they are probably original. Looks like the axles pull out on one side, or the head of them wears out because it serves as ... (cont.)

We are having a difficult time locating replacement slide rollers for 5 windows in our 4 Seasons sun room. I attached some photos and some dimensions.

Hello, I am looking for window rollers for 2 radco series 800 weather lok windows. Not sure about the correct size or dimensions. Also the last picture shows the top of the window with a plastic pin, not sure if there is supposed to be a roller there too? Thank you for your help. Paul ... (cont.)

I need to replace wheels and axles in 20 sliding windows. The windows are Radco Series 800 Weather-Loc. Roller dimensions are 7/16" diameter, 3/16" thick, with an 1/8" axle hole. The axle is 1/8" diameter. Length is 1/2" with an endcap 1/4" diameter and about 1/16 thick. The wheel id steel and ... (cont.)

Please review the attached and make a recommendation Thank you Donald B

Dear Swisco, I'm looking for some steel rolers and nylon axel pins for some sliding aluminum windows. The rollers are 5/8 diameter, 3/16 thick with a 5/32 axel hole to accommidate a 1/8 nylon pin. The axel pin is 3/4 long. Any ideas? Thanks, Dennis