Viewing all customer Discussions for:

58-176 36" Duo-durometer Door Bottom Sweep

the door sweep is 1 3/4" across and the "legs" are 1 1/8" apart by 36" long. The side gasket is 3/8 X 3/8 with a diameter of 5/8"

I have a Stanley door and am attempting to replace the door bottom weatherstripping. There is a small wooden block with grooves on each side that is rotten. Is this piece available for purchase? Thank you, Glenn

We need to replace this door sweep. I wraps around underneath the door. This is for a McDonald's restaurant.

Hello, need to replace my 36" exterior door sweep on my metal front door. I've attached pictures with ruler ref of the metal channel it will fit in and of the upper and lower section of the bad door sweep made of plastic/rubber. Keeping my fingers crossed. Thank you, Jeff

Hi, The screen corners measure> 9/16'' wide X 5/16'' thick X 1'' Long----------- The Bottom Sweep is 1/3-8''wide and has 2 plastic channels that slide into bottom of door. Please research for me ok? Thanks >>>>> Rob

Wondering if you have any of these?

Hi there! I recently moved into an older house (built in 1935). I have been looking everywhere for a replacement door bottom, but haven't had ANY luck. (see attached photo) A fellow at Home Depot told me this was an older "stanley type" door bottom. Thanks for any help you can provide in identif ... (cont.)

Hello, Can you please tell me if you have a replacement door bottom as shown in the attached photos for a steel residential door? Thank you.

Hello, house was built in 1992. Prior weatherstripping has a t-strip attaching weatherstripping to door. Can't find anything like it at local retailers. Can you assist?Thank you!Julie

I have a Lincoln wood door with t-slot weather stripping that slides into the drip edge. The top of the T is 0.1875 inches. The weather stripping has becomes ripped and damaged and needs to be replaced. I would like to know which one would best fit my door. Pictures attached. Thank you! ... (cont.)

Looking for the door weather strip shown in the picture and in the rough diagram. Do you have anything like it? Ship toCanada? Door is 1 3/4 inches thick. Thanks, Bob

Hello. I am looking for replacement door sweeps for 3 fiberglass entry doors identical (or nearly identical) to those pictured above. I am not able to provide photos of the installed sweeps without removing the doors. But that doesn't seem necessary in this case. The sample shown in the photos is ... (cont.)

I have a pair of 1978 steel entry doors that need new pvc or vinyl sweeper inserts that fit into the existing track on the bottom of both doors. Can you tell me where I can obtain this? The door is 1.75" thick. The gap at the bottom of the door it displaces is approximately .25".Thank You,Dan ... (cont.)

Replacement for a sash on the bottom of a metal door

Hello, I am looking for replacement rubber seal for the bottom of an entry door. Please see attached images to help!

My home was built in 1994. The exterior doors are steel (I think Stanley doors) and the bottom weatherstrip is a black rubber strip that seems to be embedded into the door bottom. Can this be replaced? If so, what product do you carry that can replace it? Mine was starting to peel off. I really do n ... (cont.)

I am looking for a rubber seal to my front door. I need the part where my finger is pointing in the picture I uploaded. It is a rubber seal for the front door. Right now my rubber seal has disintegrated leaving a hole between my door opening.

Looking for a replacement on slotted bottom door seal approximately 35 inches long

Door is 1987, at top of door is # 28515878 then there is a date Nov. (3 or 8?), 1987 then a number 11016. It is 36" exterior door.

Exterior metal door is designed with a small recessed area to have a bottom piece (Door Bottom) snap in place. This Door Bottom provides a weather seal between the door and top of threshold. The metal door is 1-3/4" x 36" x standard height. See four titled photos attached. Only need the replacement ... (cont.)