Viewing all customer Discussions for:

82-008K Sliding Door Keyed Handle Set, 6-5/8"

As the display picture, look like this key set use for the door open right to left from outside. Can it be used for the door open left to right from outside? Thank!

I have a 6 5/8 center line to bolts glass sliding door latch . The latch is a unit that slides DOWN to lock NOT UP. Everything I can find locks moves up. This will not fit the hole in the door. The original in this discussion is the one I want to match up to. Thank You

I need a patio door handle with a key st. and the patio door has a dns industries 13/25 outside pull and has stamp on it that says 1400 series. Do you think this would work as a replacement for my lock

Screw to screw is 6 5/8 inches as close as I can tell, Also, I have other doors with same latch assembly that I need to have replacement handles with brackets. Thank you.

Dear Sir/Madam, I have a boat in England UK on the river.I know the boat came from lake michegan originally.The boat is a BAY HARBOR.i am trying to replace a door lock.On one half it has one half(the latch side,locked from inside the cabin) 12DNS industries miami fla,on the other hal ... (cont.)

I could not find any markings and I can't explain it very well. The broken piece in the photo attaches to the inner frame (where the door closes). The lick mechanism is still intact inside the door. I have three doors with locks and their design is a pain the neck. Any suggestions? ... (cont.)

I need seven locks and one plain handle like you see in this photo. These two sliders meet in the middle of a big glass wall. Do you sell just the plain ones too? While these are white, would love stainless, or perhaps the chrome. Thanks!

I have a flush mount patio door latch (looks like your 82-008K) on my sliding door on my boat. I need a sturdier locking mechanism with a key. Any options to retrofit with a better locking mechanism? The door can also be lifted out of its track to gain entry since it is on the outer track. ... (cont.)

DNS Industries, Miami, FL Chrome, hole centerlines = 6-1/2", keyhole centerline from top of exterior plate is 4-1/2". Inside lock handle has 12 INSIDE PULL JAPAN. Also has a raised numeral 2about 3-5/8" from the bottom The inside door pull has a 'Cherry' color wood handle (1-1/8"x9"x7/16") mount ... (cont.)

I have a sliding glass door lock that is malfunctioning. When I lock the door to leave, the security lever jumps over to the locked position which makes it impossible to unlock. One part of the lock is stamped DNS Ind Miami Fla the inside part shows 16 inside pull standard dns ind 16. The outside wi ... (cont.)

I would like to add a key lock assembly to this door. Do you have one that will fit this door? As you can see it is an inch wide and the locking mechanism is for one hole only.

Hello, i would like to know if the SLIDING DOOR KEYED HANDLE SET, 6-5/8" works ok for the dns industries 12 inside pull 1400 series. I need a handle to have a key. Thanks!

hey I need to replace my patio door lock. It seems to similar to your 82-008 product. The question I had was how far the latch was from the lower hole so that it fits into the hole in the door frame. Attached is a picture of my current lock Thanks --Aditya

It looks like your part 82-008K

IS THE KEY ALREADY INSTALLED IN THE HANDLE . I HAVE BOUGHT OTHER BRANDS THAT AREN'T, AND I BREAK THE LOCK BEFORE I EVER GET IT INSTALLED

My slider door has the DNS 1014-4, photo attached. I would like to either replace or retrofit this lock with a keyed outside lock. Any suggestions?

I have lost the key and need to replace this handle with another that is similar. The Dimensions are (Length 7 5/8" withe 15/16

What is the difference between these two mechanisms/part numbers (other than the price!)???

nee to replace a patio door lock made by dns industries series 1400 12 inside pull

I need to know the thickness of this assembly.