Viewing all customer Discussions for:

26-116 Window Sash Lift Handle

I require some repair parts for Alcan hinge windowsTop latch x2Pivot hinge x4Window lift handle & hardware x10Any insight on these parts?Can they be ordered?Specifically the pivot pieces.

The screw holes are 3 1/4 inches apart. Looking forward to hearing from you. Cynthia

These windows were installed over 25 years ago. I am looking to order part 26-107 and 26-116. I am struggling to find the tilt latch replacement, photos attached. The latch on top is 2 inches long and .75 inches wid, pictures 1 and 2. Picture 3 shows the thumb latch removed and showing the inter ... (cont.)

Similar issue. I have a window slider and currently looking for replacement for the handles:

Spaced bar in IG says ROVO-80. 1st photo is the tilt lock mechanism. 2nd photo shows the handles and locks. Let me know if you need more photos. Just beginning to fix them and I am sure I will need a variety of parts.

I am looking for the attached pieces for an older window (we think 10+ years). The windows were installed by a previous owner and I cannot find any names, numbers, or markings on them. Thank you!

I recently moved into a Keller Home in Colorado Springs and wondered if y'all might know where I can get a replacement for this Window Pull? They measure 3"x3/4" The hole is 2 1/2"*1/2" The house was built 1996 Or any help identifying the Window Manufacturer appreciated.

Need to replace Gorell patio door screen handle.

Hello, We are looking for a replacement part for a Simonton window. I think it is called a lift handle. The window is in the bathroom and is smaller than the average window (lift handle measure ~8" wide). Do you sell this? Thank you.

Hello, I just bought a house and I am trying to find the manufacturer of these windows so that I can replace the broken handles on this window. The first pictures are the two broken handles, the second pictures are of a companion window with parts still intact. On the inside of yet another compani ... (cont.)

I want to add window sash lift handles (26-116) to our thermo pane windows, but I'm concerned about introducing condensation between the panes when I screw the handles on. Should I be concerned?

My spiral balances on 7 tilt windows are plastic tubes and there is no tip. There is a circular guide in the channel (IMG_0226) that will slide in the channel. The pivot shoe is 17/32 thick x 1 1/4" x 2" (15-015?) I have 7 windows with 4 spiral balances each so I assume that I will need 28 of ... (cont.)

the lift ledge you would use to pull window open is cracking at seam. is there a white vinyl replacement ledge. 27 1/2 inch wide depth of lift ledge is 3/4 inch

I have some older vinyl replacement windows that have handles on the bottom sash which allows you to open the window. There is one screwed to the window on each side of the bottom sash. The handles are nothing more than a vinyl piece that mounts on the bottom sash and when the window is closed, yo ... (cont.)

Need ten window handles like this one. 4" long and 11/16" wide. Need any other infor? Thanks Mike

I need at least 12. If they fit and look good in my kitchen I will replace my whole house with them

Hi, I've got some pretty basic single hung vinyl windows that are about 14 years old. They do not come with a sash lift on the bottom of the sash to help pull down the window after opening. This is becoming more of an issue as a lot of windows are really tough to bring down now. I've tried removing ... (cont.)

what is my best option for fixing this full length lift handle and make it look good. not sure of the length because I couldn't find my measuring tape, maybe 14-17 inch. Maybe grind it off and put 2 lift handles?

I purchased several parts numbered: 26-147. The part might work well in a way I am not able to figure out. I have the sliding vertical windows except the window wouldn't close entirely when the handle was in the place needed. Is there an alternative way to alter the window frame etc. so I may try th ... (cont.)

Do item 26-116 come in a bigger size. This is the style pull handle I need but not long enough