Viewing all customer Discussions for:

90-278 Lock & Keeper, 2-1/16"

I need your help again, this time a center lock for a tilting vinyl window as pictured. The screws are 3" apart. (If the only replacement available has screws further apart, that is OK since I can drill new holes into the frame.)

Trying to find and purchase about four of these sash locks and keepers. The keeper is about 2.5" by 1/2"

Hello, will the part # 39-429 (right handed) and 39-430 (left handed) a replacement for my casement window crank? Are there other options. I also need to replace my window locks and keepers. Locks = 2-1/16 for installation hole and the depth is 11/16 and the lock itself is 2-7/8 Keepers = ... (cont.)

I would like to purchase # 90-077A , I need it to be 2 1/16 x 9/16, not 7/16 it's for a 20 year old Jeld-Wen window. Thanks

Truth Window Lock / Entry Gard is wrong size (too thick) need 90-161 with narrow keeper and 2 1/16 spacing. I already ordered and tried 90-077C and 90-279 and they were too thick so I think I need the 90-161

Selling House, Inspector said 4 of the locks were broken and just sitting on top of lock. I've attached picture of non broken lock, and one of lock that latch is broken from and the top and bottom of the latch. I have four of these that are broken. Do you have replacement parts that I would need to ... (cont.)

2002 windows that needs some replacement parts. I have to work on 17 of them

Window lock for picture window

I am looking for replacement locks for my window, it's 2 1/8 hole space on the lock and 11/16 on the backset. The backset piece needs to be flat in order to work on my window, as the thicker ones wont let the window open or close

Have same setup 90-286 is correct but I need keeper 2-1/6 x 5/16 deep.

Original windows on the 5 y/o home we just moved into has plastic locks, and the levers break easily. Need metal replacements.

Looking for parts. I bought a set of Jeldwen white Vinyl windows from Home Depot in 2003. The wen locks/keepers and the (weak) "security locking pin" assembly (plastic tab to allow window to open only 3") all need replacing. The stationary parts are both 2.25" (pair of screws on centre), and the w ... (cont.)

Hello, I can't find any identifying codes on these pieces except MDO in the middle of an imprint of Texas. I think there is also the number 5 or 6 below the MDO, but it's not super clear. I've attached the "top" and "bottom" of the two pieces I need. (I need several of each.) Anyway, I can't fi ... (cont.)

I need a replacement part for an empire window latch. It has 373 stamped inside. It is approx 2 3/4 long and 1 inch wide.

I need to replace both the locks and the keepers for Advanced Window Corp windows. The holes on the keepers are 2-1/4" apart. The holes on the locks are 2-1/16" apart. Please see pictures for additional dimensions. Thank you!!

Hi, I would like to order Viking Window Lock as per picture. Please advise me what I can do. Thanks.

Need two complete units. Not sure if you have them in beige like the ones I have but I can use white if not.

All markings are shown on my photos.

I am looking for a sash lock-mounting holes are 2 1/16 and offset is 11/16. It is die cast white. Thanks Alex

I need to replace some sash locks in my home and can't figure out what I need. I saw one that looked like it would fit but wasn't sure. I also need wool pile for one of my windows and I didn't want to cut it out before I had a replacement. It doesn't slide right out so ai'm assuming I'm gonna have t ... (cont.)