Viewing all customer Discussions for:

90-278 Lock & Keeper, 2-1/16"

window #factory order-54020;window order-6000;made 8/15/01;27 3/4 * 53 1/2 ;window#-120-834980;widow lock has #8100 and j31 stamped in inside;mounting hole to mounting hole looks like 2 1/16;from front edge of lock to mounting hole looks like 11/16.Not sure if local Alside dealer would have this.any ... (cont.)

I can only see letters EPI on it

Need price and availability per the attached. Size: Length =2:75

Hi - I am looking for the lock in my pictures. The holes are 2 1/16" on center and 11/16" from the window side of the latch. The numbers on the bottom are 8300-02 on the white piece and 8303 on the gray piece. There is also a 1 to the left and down from the 8303 on the gray piece. The white ... (cont.)

Hi I think this is pretty old but any chance you can locate one of these EPI locks? Thanks Neil

Hi, This lock has a keep that meets the lock at 90 degree position. It has 2 1/16 hole center. I cannot find any that may work to replace this lock.

I need two window latches (philips); the pert that attaches to the sliding part of the window and locks it with a lever. The levers have broken off mine. The distance between the screw holes is: 2 1/8" and the overall width is:2 & 3/4". The name "Philips" is on the "front" of the piece and the word ... (cont.)

Window is Empire Pacific 4200 Series installed in 2005. Please give me a quote to replace the lock/latch item shown, which installs on the left side of the sliding window (i.e., the rightmost window in the full window image). I would like two latches matching the broken one and also one latch th ... (cont.)

Greetings and thank you for providing this service. I'm hoping you can help me to identify these window locks. They were on the windows of a condo I purchased near the beach and salt air has corroded them to the point that they require replacement. Certainteed has gone out of business but I'm hop ... (cont.)

Lock strike screw holes 2-1/4" apart center to center. The screw holes on the slider window is 2" center to center. Hope this help find one!

The windows were supposedly made by Philips. The latch is ok but the keeper is broken where the latch connects to the tang. (You'll notice the picture is of an unbroken one,) Didn't see a match but there does seem to be a couple that I could possibly adapt by shortening the width as it mounts unde ... (cont.)

The latch is broken I have attached a picture of the broken one and a picture of a working one. Any help would be appreciated, I have not been able to source this locally.

This part is the security lock/ latch in a Philips Product window in prefabricated home. The component that is attached to the upper window section (stationary portion) has broken across left side. I appreciate your assistance in finding out what part/ parts are needing to be replaced. ... (cont.)

Dear Swisco, Hi, I

Need replacement. Possible window no.9728

I need several things for my old Viking aluminum windows. When I spoke with a rep n the phone yesterday we could not identify my two locks. The first picture is the lock that goes on a window that opens top to bottom. It is 2 13/16 from the far edges and the holes are 2 1/8 on center. It has ... (cont.)

Looking for Marquee window parts Balance with shoe 30" balance string on the top Lock 2" between holes Keeper 1 1/2 Wide 1" high 1" between holes Single hung windows tilt in.

Window Latch on the Anderson SivlerLine Double Hung Window. NOTE: 1) One of my photos shows the Latch and the Receiver. I need the Latch (larger part with the rotating Lever) not the latch receiver (thin part). The following numbers/letters are imprinted on the bottom inside of the latch: 1) ... (cont.)

Distance between screws shown in pictures is 2-1/16". Windows were made in the mid to late 1990s.

the dimension from screw hole center to screw hole center is 2" the keeper dimensions screw hole center to screw hole center is 1 1/2 " the latching mechanism is some kind of metal alloy thanks for your help... pat