Viewing all customer Discussions for:

90-278 Lock & Keeper, 2-1/16"

Having a hard time finding replacement locks for a few broken ones in our new home. On the lock, the holes are 2 1/6" apart and from the holes to the edge of the lock is 1". The lock height is 1/2". The keeper holes are 1 7/8" and the closer, raised mount holes are 1" apart center to center. The ... (cont.)

Canon find any markings or numbers on hardware.

I am looking for a window latch that will fit existing window.

Prism broken latch

Need missing top check rail glazing bead. Upper window is missing the bottom peice of beading that retains the glass, AND which the latch is screwed into. No window brand info. Can't find bead of correct profile/cross section. Tilt in lower window. Windows approximately 10 yrs. old. Any help appreci ... (cont.)

I need help in ordering this correct window latch. I tried ordering myself but ordered the wrong latches. I will attach pictures with hopes you can help me oeder the correct ones. Thanks Brad

I need the entire part to put on the window- both pieces. The one side broke.

I am looking to replace one of these Cam Locks that were installed in 2019 with 3 Replacement Vinyl Windows. I posted the Cam receiver so you can see what the Cam actually engages with. I have not been able to find anything close with a 2 inch hole spacing. The screw hole set back is 11/16" which se ... (cont.)

Hi. Could you please help me select the correct face mount keeper to replace this broken one? Thank you

I have 2 sash locks that need replaced ASAP! I have orded tilt latches from you in the past and these replacement will be for the same color window frames.

The lever on one of our sash window catches is sheared off. See one of the photos for a label from one of the windows which I believe identifies the brand (STILES)? The other photo is of subject catch. We measured screw centres to be 2 1/16" apart. I'm assuming a complete catch replacement is requ ... (cont.)

I have provided a serial number and photos of the part I need.

Am trying to replace various parts on my windows. House was built in 1998-9. Parts needed include several balances (measure of covers are 29" and 34"), balance shoes, one pivot bar, one balance tension tool, one window lock. Only brand I see on window is MW which is on lock. The balance shoe mode ... (cont.)

Not sure if this helps but this is the info located on the stickers inside the windows. ANSI/AAMA/NWWDA 101/IS H- R25 - 96 RP SERIES: 40 - 06/40 - 17SH 4766858/02 Unit: 35.5000 62.5000 4?? 4EB4EB G1: 31. 5000 28.6875 FCSH Norandex, Inc. /Valparalso 94 Simonton Windous 0308122056 8/13/03 F0285 812 ... (cont.)

Hi,I need to replace a bunch of these EPI window latches, but don't know what replacement parts to order. Thanks for the help.Dan

Bright white window Camlatches, left locking with Alignment Lugs. Mounting holes are 2-1/16" and 11/16" for vinyl clad double hung windows. The latch mechanism has a 680 stamped on the back I am a remodeler and homeowner here in Boise ID area

Good afternoon, I am in search of this lock. Its from a Nami window series 600HS i measured from center to center and looks to be 2 1/8 and from top to center is 11/16 There is a #1 on the inside lower left corner

Need help determining which window lock is the correct replacement part for our windows. The only numbers I can locate are on the bottom the piece with the locking mechanism, a 10 and then a 02 on the base. Thank you for any assistance!

Hi, I'm in need of several 2.25 inch window sash locks with keepers. There needs to be a 0.75 inch backset among the holes of the two parts. Do you have anything that fits that description?

Hi, I wish to replace original window locks and keepers. I think they may be PrimeLine but not sure as probably original to house (2003). Space between drill holes on both pieces is 2 1/16. Have found replacements that have these measurements but the location of the drill holes location differ, due ... (cont.)