Viewing all customer Discussions for:

58-135 25ft Bubble Seal, 3/16" x 11/32"

Hello, We would like to replace the sash balancers and bubble seal for all windows in our home. We need 14 balancers and 25 feet of bubble seal. The balancers we have are 30 inches with 2920 for a 14lb non tilt window. The channel top is winged and the channel show is winged. The show appears to ... (cont.)

I Have in my cart S380-30 and S380-35 but my plastic piece at bottom of the balance measures 7/8 not one inch and I read some comments that I may need 029 (from Memory) on bottom and you have to make up. Please let me know about this. Also the bottom `Bubble Seal", please see photo, is not exactly l ... (cont.)

I have 7 windows I need balancers for. Five of the windows have a stamp number of 2940 (BSI) on the aluminum rail and are 30" long and 1/2" wide. One has a stamped number of 1730 and is 18" long and 1/2" wide. The last one has a printed number of 29 9 FS CALDWELL and is 30" long and 1/2" wide. I ... (cont.)

Looking for this window seal. This is a bubble seal but the slot is on top not on side. I couldn't find exactly like this on your website

Bottom window seal. Appears to be replacement. 25FT BUBBLE SEAL, 3/16" X 3/8" Product Code: 58-135

I have pics

I was not able to locate this weather stripping. Please provide ordering information. I appreciate your assistance.

I have four pairs of Alcan sliding glass doors that need the white weatherstrip that seals the edge of the door on the outside and inside when closed. Attached is a cross section photo. The width of the "T" is approx 5/16 inch wide and the bulb itself is about 5/16 in diameter. You can see in the ph ... (cont.)

I am looking for the replacement seal for the bottom of my vinyl windows. I'm not sure what it is called. It slides into a 3/16" groove on the window frame. Let me know what other information you may need to identify it. Thank you.

I previously ordered a commercial bubble weather strip from your company that was to small, the size I ordered was 9/32." I need one that will fit the dimensions in the pic. Strip width = 1/4" and tube approximately 3/8" wide in diameter. I included pics for reference. Any suggestions?Best Regards,G ... (cont.)

Hi guys,My windows are not keeping the cold air out. Do you have any replacement parts for vinyl Windows like the attached. The sides are two circular tubs, one tube gets inserted in the channel. The other is supposed to seal the gap between the window frame and the window but it's not working well. ... (cont.)

Am looking for replacement of weatherseal for CertainTeed casement windows The T-Slot is 3/16 but am not sure what the shape of the foam insulation was as the photo's show.

one photo of screen needing replacement; do you sell screens. two photos of bottom of window of apparent plastic weather strip held in place by screws--do you sell these?

I'm going to assume that I need Part# 55-174. Of the three windows two are fixed in place with no way to remove the old brittle glazing without digging it out in pieces. Am I correct? If so do I just press the new glazing in the gap?

Hello, I have older aluminum windows in good shape, but the bottom sash weatherstrip seals are a bit hard and are too narrow. Do you have the replacement part to fit these windows for a tighter seal? Does this come in a roll? I have 9 30-inch-wide windows, 2 seals for each bottom sash. Thanks. ... (cont.)

Hi, My Simonton double sash windows are in need of new weather stripping. Please review provided pictures and recommend weather strip replacement. Thank you.

Looking for this part,

1/4 inch is the - part of it and the round part is 1/2 inch and I need at less 8 feet

Please identify the replacement weather strip needed for my 1996 certainteed vinyl casement windows. This is in a T shaped groove toward the exterior of the window.

This seal is approximately 5/16 and the T is 3/16, do you have anything or point me in the right direction