Viewing all customer Discussions for:

39-107FK Truth Folding Handle And Cover Kit

Hi I am looking for the following parts for the window references above. Can you assist with part numbers if you carry them? Left split arm operator w/handle and cover white (crank arm 9")hinge arm(5 1/4") with bushing and guide track Hinge channel and pivot armsPlease let me know if you need any o ... (cont.)

Hello, I'm in need of these replacement parts. The piece on window measures 13.75 inches. We will also need if possible window crank shown in picture. The part these latch pieces fit into B 19 1 and 2 measures 5.25 from top to bottom. I believe these are Pozzi parts. I heard they were bought out by ... (cont.)

Seeking direct (or equivalent) replacement for this window operator from 1993. (see photo)These are not broken, but the original design has always had excessive free play within the gear train, allowing the windows considerable movement. The end of the (~ten inch) arm can move by almost 2" just du ... (cont.)

Hello. 3 Marvin window crank handles (only) need replacement.

Hi ! I need to replace some broken and stripped operators but I am not sure of the part#. Could you point me in the right direction?

Hi, will this fit the truth hardware model attached in the images below. Or is there a folding crank that is compatible.

Long arm measures 9 inches Short arm approximately 7 1/2

Looking for the connector part(s) that mate the crank to the sill hardware. Thank you!

Hello, I'm working on a home remodel and need to find new crank covers and locks for two types of Pella Casement windows. The Home owners have repainted and need white and black window hardware. I don't have model numbers only photos of the existing hardware. Hoping to get some help! ... (cont.)

I can't read the final letters/numbers on the assembly due to rust. I think it is ZO. Those last two appear to be letters as they were thicker than the numbers. We have not removed the assembly so I don't have a picture of that but we did take off the "cap" hiding the mechanism and I've sent a pi ... (cont.)

I have two (2) non-functioning Truth Window Operators. One right and one Left. I'd like to find replacement operators for these windows. They will open the windows, but both cranks back out of the stem instead of closing the window. Can you tell me what replacement model I would need? ... (cont.)

I have a casement window that has an operator that opens but does not close the casement window. I need to replace the casement operator. See photos to determine which casement operator is needed as a casement window operator replacement. Please, tell me which casement operator is needed to repla ... (cont.)

Numbers on the device Base 40372 Gear Box 30880 Long arm underside 30472 RH Short arm 30842 R Short arm extension 20810

What is the size of the bore hole for the 39-375? Is it 11/32" or 3/8". I bought what you recommended (39-107FK) but the bore hole is too small. I need to replace a folding crank with stamp of C 1080-3A. Thanks very much

My window openers part broke while using on winter. I'm looking for accurate parts. Help me to find it please.

To whom it may concern, I am an architect and a client is asking for help with one of his windows which crank have come apart and I'd like to see if you sell a preplacement for it (hopefully matching color). Please see attached pictures. The last pictures of the opposite side window, which is funct ... (cont.)

Hello, we are in need of a crank out window crank, all we tell you about it is that the guide which is still attached to the window is 11 1/2 inches long, the opening in the window where the crank goes is 4 inched wide, the mounting holes that are visable on the window are two sets, the holes furthe ... (cont.)

Photo attached. The handle will open window but will not close it. Do I need just a new handle or what

Old Truth operator that rusted out and does not work properly. I see a few numbers including 3084IL and 20544. The operator is located on the right window casement as you look outside. Thanks

Hi Experts, I have old Caradco hardware on all my casement windows and am looking to replace one set of hardware that's broken: - One window lock, see pics IMG_1752 (front) and IMG_1748 (back). Number on the back side of lock is 40223 - One window crank and cover, see pics IMG_1742 and IMG_1741 ... (cont.)