Viewing all customer Discussions for:

81-310 Roller Axle Repair Kit

I have 94" high x 48 wide mirrored doors. They are extremely heavy. I need 6 rollers. do you have replacement rollers for me?

width 11/16 inch heigth 1" wheel diameter 1 1/4 inch material nylon

1" tall, width is 13/16", wheel is 1.5" and is concave

Hello, these doors are old but if you have anything that would work, we got im guessing 20 doors like this that I could purchase some spares for im guessing at some point we will have more problems with other doors Thanks

i am looking for this wheel. Which wheel should I use in your website. Do you have the plastic wheel version. The original one has plastic wheels . It is installed on mirrored sliding closet doors. Thank you

Is there a replacement for this or something i can make work? length 3 1/4 width 3/4 height 1 3/8 Wheel 1'

Looking for replacement wheels for: Single pane, aluminum, roughly 60" wide by 80" high sliding tempered glass door from Tom Lowe, Hillside home in 94611 built in 1969, contemporary.

Hi, I'm looking for replacement rollers for my mom's sliding glass door. The aluminum glass sliding door has two rollers and uses a pin through the door Nd the roller to lock into place. Do you have anything for this

I didn't see any significant markings. outer wheel diameter is just over 1.125" inner wheel (center groove to center groove) is approximately 1" chassis is 1.250" tall x .625" thick and 3.125" long

Wheel O.D. Is 2", width is ≈7/16". The assembly bodies seem much simpler than most of what task carry. I think the door is from the 50's.

Wide 5/8 inch, high 7/8 inch single plastic roller

I have struggled to replace this. The roller is 1 1/8 inches. I can only find 1 1/4 rollers. Neither side is in good shape would like to replace both complete parts, not just the rolled if they are available. Patio door is 20+ years old.

1 1/2. With a 1/4 INCH BORE..I NEED

Had to remove the bottom piece from the door and knock out the existing rollers from either end. Measurements seem to be about 3" x 1" (maybe a bit more plubs 1/16") x 11/16"

I have attached 3 pictures. There are two rollers per door.

Hello, I have been trying to locate a replacement for the pictured door rollers. What seems to make this difficult are 2 things - 1) Roller wheel is 1 inch diameter and 2) It appears to be called an F tab where it attaches to the underneath of the door as apposed to the end. On one of the pictures y ... (cont.)

We have unique rollers here for the screen door portion of what I believe are Kawneer doors. I could be wrong. To note, they screw in from the top as well. So I have to remove the rail of the door to get to that screw. Any help finding replacement parts would be greatly appreciated. ... (cont.)

Original 60's era heavy aluminum sliding glass door. Need to replace rollers pictured. No markings on door for manufacturer or anything else. Roller says 'General Bearing Mineola NY'. Roller wheels are 1 11/16 inch diameter, and 7/16 inches wide. I think with a 1/4 inch roll-pin axle about 3/4 inch ... (cont.)

I am trying to find replacements wheels for my 8 foot glass patio slider doors. The dimensions are length 2 1/4 inch Height 1 5/8 in Width 7/8 in and wheel diameter is 1 3/4 in This house was built in 1959 in Northern California and ChatGPT seems to think it is from the Arcadia doo ... (cont.)

Sorry, but there is no part number on the wheel assembly or the aluminum door itself. They could be original doors from when the house was built in, but really have no idea. Wheel: steel, 1-1/4 inch Height: 1-9/16 inch...maybe 1-5/8 Length: 1 inch Width: 3/4 inch