Viewing all customer Discussions for:

15-001 Channel Balance Shoe, 1-1/8" Depth

the top and shoe are not same. BSI 2830 need help find 20

I need to replace a number of balances, the numbers stamped on the channels are: 2810 BSI, 2830 BSI, and 2440 BSI with a backward C. Having trouble identifying the balance shoes. The top shoe I am confident is a 19-002, however, the bottom shoe could be either a 15-001 (series 390) or 15-005 (ser ... (cont.)

This is a channel balance from an aluminum window, Alenco circa 1985. Has marking of 27 C. Measures 28 inches. I have identified the top piece as 19-002 but have not identified the bottom piece, or at least one that is close and might work. From looking at other customers post, possibly the S390 ... (cont.)

Do you have a balance with a part# 2230 stamped on it? Also the attached lock assembly? Thanks

I am looking for the replacement balance for my 25 year old Alenco windows. I also need the replacement vinyl weather seal at the bottom of the sash.

Hi Customer Support, I need 10 pairs of balances that look like this for the windows in our house. See attachments. Do you have the parts?

I can help you pick out the right balance for your window. Take a look at the 15-001 and 15-002 and tell me which is a closer match to the shoe on your broken window balance.

1/2'" channel balance for PGT window. Need both left and right. Looks like 19-005 on top and either 15-0001 or 15-002 on bottom. 29DS 1/2c 37 marked on back.

Hello, this is my first time replacing a channel balance. I have Alenco Windows and the images below are the channel balance that I need to have replaced. I have a 1/2 inch channel balance for non-tilt window approximately 16 inches long but I am unsure about the top and the shoe difference and was ... (cont.)

There are no numbers stamped anywhere on the balancers. Included are photos of the top and bottom of 1/2" x 29" balancers that I cannot verify from your photos. I hope these photos will illustrate which units I might have. All windows are the non-tilt out type aluminum windows. I also have a sin ... (cont.)

Hi there, I would like to see if you have a replacment for the balance spring. I have attached the pics. The window size is 29-1/2 tall;however the balance spring is only 26" in length with out counting the clips. Please help advise. Dan

Hi, I looked through your balance images, but could not find an exact match. The attached photos will hopefully let you figure it out. These are from two windows weighing 34 pounds each (four springs total). I noticed that the numbers on the side are different. Channel Width: 1/2" Channel ... (cont.)

Attached are photos of window balances that need replacing (circa 1983). Have included photos of the stampings (14A, 20C, and 24B)on the metal channels. Also need some 24C channels and a 26C channel. Does the A, B and C refer to the weights in the channels? All of the balance shoes are identical ... (cont.)

I have a Viking non-tilt vertical sliding window where I need a pair of Channel Balancers replaced. These were purchased in 1995 from Home Depot. I have shot photos of the ends. The original balance is stamped BSI 2630 B4, the metal portion is 27 inches in length. Can you point me to the ... (cont.)

I need Channel-Balances for 2 windows, pictures attached, Can you pl give part numbers

Thank you for the awesome website and help with identifying my replacement part....I await word from you.

Metal channel is 23' long. Don't see any that match.

I have two different length balancers. One is 22 inches long and has a stamp on it 21 12 BS1 One is 28 inches long and has a stamp on it 27 4 BS1 Please advise. I need 8 of the 22" and 4 of the 28" Not sure what the stamps mean. The windows are already installed on a house I just purchased. ... (cont.)

29 inch long, with 2830 then an upside down G and then a vertical B.S.I I found some options on your site but they seem to be "close" and I was concerned about getting the exact fit. Please confirm what I should order.

I'm trying to replace my channel balances. The label on the window frame reads "Series 710 H-R40-48x84". The channel balance on the right side (viewed from the inside of the house) is stamped 27-3 as seen in the picture. The left balance is too damaged to read the stamp but it appears it might say ... (cont.)