Viewing all customer Discussions for:

32-057 13-3/4" Self-Closing Drawer Slide Pair

Hi all, could use an assist with this one. Need to replace a broken kitchen drawer mount. Slide opening is 1 1/8" Everything I've found is much smaller.

Slider on the drawer side of 5 drawers were bent and hard to open. Existing sliders have a smaller roller/wheel. Hoping to find a replacement for the drawer so I do not have to replace both sides. Cabinets were installed in 2004 There are no markings visible on sliders. Appreciate any assistan ... (cont.)

Hi,my name is Singh and I am looking for that plastic holder clip which is holding drawer side rails for the drawer. Can you guys let me know if you guys have that plastic clip part.

I've been to several hardware stores trying to find a drawer glide that will work with drawers in my kitchen that have had the glides break. I need a glide to mount at the back of the opening which will support the track that holds the drawer. I've attached some pictures to give you an idea of wha ... (cont.)

2 1/2 in. Long 1 3/4 in wide (kitchen). No Model #

I have ordered several replacements and not have been the correct size. The issues I've had is they are too narrow for the slide to get into the bracket. There is no markings or any identification on the part. If you could help I would appreciate it.

This opening for the slide to fit in is 1.25" All of the new ones I find at hardware stores are 1" or 7/8". Can I find this size anymore? Cabinets are about 20 yrs old

This is a plastic drawer slide guide that goes in the back of the cabinet. The metal slide goes in the plastic piece. I do not have the name of the company that installed the cabinets nor do I have the name of the cabinet as these were installed when the house was built. Kindly let me know if you pr ... (cont.)

The top set is from a pull-out drawer in kitchen. The bottom set is from a drawer in our den. No part numbers are displayed on the parts. These are both from cabinets installed in 1991. Can you help me to determine as to which replacement parts I need for the sockets and glides if necessary. ... (cont.)

My drawer left slide(facing my drawer) got bend I need an replacement part with screws .. bend slide has Unigrass 6600 mark on side and 5 G on the other side.

The drawer guide attached to the drawer, the Plastic roller wheel broke off. Need to replace two.

I need the slide part of this track for both sides. Where could I purchase those?

drawer roller, rear of unit

The part is .500L x .500W x .375H with a horizontal slot that is about half way through (.250). NOTE: the slot bottom profile is more complicated than "half way through" but would require a sketch to describe clearly. The slot is how the glide is held on the drawer track. The glide is captur ... (cont.)

How would these slides be mounted on the bottom? Will any screw work to keep it in place? Thanks

I am missing a drawer mounted slide for my dresser, it measures 15 inches, I have been unable to find a 15 inch replacement anywhere. Suggestions? Can I use a 14 inch, if so any special directions? thanks, Nancy

TWIMC, The little wheels/rollers came off the side of a dresser drawer. The drawer itself has heavy duty metal sides (6" x 14-1/2") and the drawer front, back and bottom are wood/MDF. There are plastic brackets attached to both sides at the top back, where the metal sides meet the wood back. Thes ... (cont.)

I have a bathroom vanity with a drawer assembly that has a pair of 1/2" (Outside diameter) wheels that fit into a metal track. The wheels (one on each side of the bottom of the drawer -- in the very back) are attached to back of the drawer with two staples. I would very much like to locate a pair of ... (cont.)

I need a few replacement nylon rollers for my drawer slides. The rollers I need are 7/8 inch, with 1/2 inch holes. The first picture is of the drawer slide without the wheel. The second picture is of a complete drawer slide. The third picture is of the broken wheel. I would appreciate any hel ... (cont.)