Viewing all customer Discussions for:

32-058 15-3/4" Self-Closing Drawer Slide Pair

Drawer guide rollers have the name GRANT stamped on the metal bracket as well as DL (drawer left) and DR (drawer right) on each corresponding bracket with 10/16" diameter nylon ball bearing flat edge wheel. I'm looking for 12 sets (24 wheels) for my mothers 1980 kitchen. I really only need new rolle ... (cont.)

I have a Mepla (label on the bracket back support) 543.000 55.02 are the identifying numbers on there. The bracket holds off the face frame in the front approx. 1" to 1-1/4, maybe 21" in length. 2 nylon wheels a set of small spikes that goes into the back of the drawer itself and screws in under the ... (cont.)

Need replacement for rear mounting bracket for glides; cabinetry installed back in 2006; probably discontinued by now;

Hampton Bay cabinet. The back mount which holds the drawer side rails has broken. The part fits in two holes in the back of the cabinet, and the "L" end of the side rail slides into the part.

this is for epoxy coated side mounted slides. it mounts into the 2 holes in the back of the cabinetW= 1 1/8L= 1 7/8slot for slice= 7/8pegs= 1 1/4 on center

Hello, wondering if anyone can identify these and if they're still available? Thank you, David

Unigrass 6600 slider and adjuster needed.

HelloI am Having difficulty finding the replacement bracket from my cabinets that were installed in 1995 it is a euro type the length is 2 1/2 inches and the width is 1 1/4 outside with in 1 1/8 inside width. Do you have this part? Thank you so much for your help.Dina

Hi all, could use an assist with this one. Need to replace a broken kitchen drawer mount. Slide opening is 1 1/8" Everything I've found is much smaller.

Slider on the drawer side of 5 drawers were bent and hard to open. Existing sliders have a smaller roller/wheel. Hoping to find a replacement for the drawer so I do not have to replace both sides. Cabinets were installed in 2004 There are no markings visible on sliders. Appreciate any assistan ... (cont.)

Hi,my name is Singh and I am looking for that plastic holder clip which is holding drawer side rails for the drawer. Can you guys let me know if you guys have that plastic clip part.

I've been to several hardware stores trying to find a drawer glide that will work with drawers in my kitchen that have had the glides break. I need a glide to mount at the back of the opening which will support the track that holds the drawer. I've attached some pictures to give you an idea of wha ... (cont.)

when you say this drawer slide is 17-5/8" 32-059 where are you measuring from? My drawer is 16" from the back side of the face or stile to the rear most part of the box. will these slides work or do I need the shorter version?

2 1/2 in. Long 1 3/4 in wide (kitchen). No Model #

I have ordered several replacements and not have been the correct size. The issues I've had is they are too narrow for the slide to get into the bracket. There is no markings or any identification on the part. If you could help I would appreciate it.

This opening for the slide to fit in is 1.25" All of the new ones I find at hardware stores are 1" or 7/8". Can I find this size anymore? Cabinets are about 20 yrs old

This is a plastic drawer slide guide that goes in the back of the cabinet. The metal slide goes in the plastic piece. I do not have the name of the company that installed the cabinets nor do I have the name of the cabinet as these were installed when the house was built. Kindly let me know if you pr ... (cont.)

The top set is from a pull-out drawer in kitchen. The bottom set is from a drawer in our den. No part numbers are displayed on the parts. These are both from cabinets installed in 1991. Can you help me to determine as to which replacement parts I need for the sockets and glides if necessary. ... (cont.)

Medallion kitchen cabinetry Wheel or caster on side of slideable drawer

Do you have anything to replace this slide? 2@undermountedon bottom of cabinet . Wheel shaft broken ,Total length of slide is 16 3/4 " . The drawer itself is 32 1/2 x 16. Hope that helps? They are schrock cabinets