Viewing all customer Discussions for:

32-060 19-3/4" Self-Closing Drawer Slide Pair

I need drawer slides for an old Quaker Maid cabinet, back when they were made in Leesport, PA. They are either 19" or 21 1/2 ". Any hope for me? I could also use 7 magnet kits for the doors.

Slider on the drawer side of 5 drawers were bent and hard to open. Existing sliders have a smaller roller/wheel. Hoping to find a replacement for the drawer so I do not have to replace both sides. Cabinets were installed in 2004 There are no markings visible on sliders. Appreciate any assistan ... (cont.)

Hi,my name is Singh and I am looking for that plastic holder clip which is holding drawer side rails for the drawer. Can you guys let me know if you guys have that plastic clip part.

I've been to several hardware stores trying to find a drawer glide that will work with drawers in my kitchen that have had the glides break. I need a glide to mount at the back of the opening which will support the track that holds the drawer. I've attached some pictures to give you an idea of wha ... (cont.)

when you say this drawer slide is 17-5/8" 32-059 where are you measuring from? My drawer is 16" from the back side of the face or stile to the rear most part of the box. will these slides work or do I need the shorter version?

2 1/2 in. Long 1 3/4 in wide (kitchen). No Model #

I have ordered several replacements and not have been the correct size. The issues I've had is they are too narrow for the slide to get into the bracket. There is no markings or any identification on the part. If you could help I would appreciate it.

This opening for the slide to fit in is 1.25" All of the new ones I find at hardware stores are 1" or 7/8". Can I find this size anymore? Cabinets are about 20 yrs old

This is a plastic drawer slide guide that goes in the back of the cabinet. The metal slide goes in the plastic piece. I do not have the name of the company that installed the cabinets nor do I have the name of the cabinet as these were installed when the house was built. Kindly let me know if you pr ... (cont.)

The top set is from a pull-out drawer in kitchen. The bottom set is from a drawer in our den. No part numbers are displayed on the parts. These are both from cabinets installed in 1991. Can you help me to determine as to which replacement parts I need for the sockets and glides if necessary. ... (cont.)

The brackets I need seem to be very similiar to your # 32-012 however the opening to slide the sliding brackets needs to be wider. About 1 1/4 ". This is for Brandom cabinets that are manufactured in Texas and they no longer have them available.

Same as above question but mine measures 20" in length. Local Home Depot does not carry. Any suggestions? Thanks

Need to know if I?m ordering the right part?

Swisco; I need to make an additional new drawer for a bathroom vanity. The existing drawer slides are marked UNIGRASS 6000. The parts are 20" long. Included are pictures, (Due to size, you will receive two messages) following is a list of hardware I am looking for. Can you help me? A) drawer track ... (cont.)

What is the part number for the rear drawer slide socket that matches 32-060 : 19-5/8" Self-Closing Drawer Slide Pair. Thanks

I need to replace kitchen cabinet drawer slides for 2 large drawers that have a built in lip on the drawer sides. The existing slides mounted to the inside of the cabinet are 19 5/8" in length, but are only 1 5/16" wide at the end with the wheel.The projection of this end is 1/2", but the wheel is b ... (cont.)

20inch long with plastic ball bearing wheel. Lever action stop. Cabinet side of drawer slide K-V No 1300 CR

I need a draw slide for a Grant 336 20 inches. Do you have that available.?

I just received my 20" 32-060 self-closing drawer slides and am wondering if there is a template or measurement instructions for mounting them both on the drawer itself and on the inside walls. Or do they just go exactly in the middle of the drawer side and matching position on the wall. ... (cont.)

Grant drawer slides 238 - 20". I need 2 pair. Photo enclosed