Viewing all customer Discussions for:

Door & Window

Hi, Looking for these that actually looks like the one used in your "How to identify" video. ( https://www.swisco.com/videos/view189 ) but need to be sure before ordering. I also need some of the frame clip that retain the channel balance also as attached. Thanks for your help

I need to replace a channel for window horizontal slide. CmC 34 stamped 28-6

I have some older ALCAN windows that I think are called sash style. The top window is stationary & the bottom window slides up over the top. Most of the locks need to be replaced. The look very similar to your 90-180 but brown with 2 1/4 hole spacing. The keeper mounts a little different than your 9 ... (cont.)

Slide-on door sweep for condo new in 1979. Door is 36" wide, 1 3/4 " thick. About 1/2 gaps to fill under door. Nevermind the rust in the photo. Replacement sweep is for another less rusty door.

Plastic with brass roller, 9/16" long, 5/16" wide

I have a patio door with a sticker on it that indicates 5500/5700 series. I'm looking for the fixed door bracket. The width of this bracket is 1 inch 5/8 the overall length is 4 inches. The back side of the clip has a step on it. The lower part of the clip mounting to the panel is 1 inch 1/4. This c ... (cont.)

Two of the hinges snapped. Do not know if there is a replacement for this. Some kind of rod........ See attached Photo.. Thank you

What measurements do we need to request from our client to order replacements for ALUMAX Spiral Balance?

The style is similar to your 89-003 model. I'm looking for a model with a longer nose projection. It needs to have approximately an additional half inch to catch the door lock.

Hi All, Here's a couple of pics of window glazing beads for which I'm looking. The first has a fold over element on top which has fallen off. I'll appreciate your guidance. Best, Note the 3 text line on the one should read 5/16" and is approximate.

I am looking for a replacement door latch for a 6 foot Peach Tree Patio door. I can't seem to find any info on the present locking system. Its brass and is on a door with a three point locking system. The date on the inside of the handle is Aug. 8th 1995 Let me know if you need more info. Let ... (cont.)

I need 4 of these. I am a return customer and these are from the same model house as my past orders.Keith

Have a window that needs tilt locks

MY door is a 15 lite exterior french door w blinds between the glass purchased ~ Sep 2005 I need a locking assembly. The only identifying mark was a QA stamp dated 11/25/2004 Main body of latch is 8". depth is 2 1/2 inches. The face of the latch has 2 "ears bringing that measurement to 9 3/16. This ... (cont.)

Have sash control with patent number D466787 on back. About 915/16" overall length with mounting screw holes at 4" Dark Bronze Also, Amesbury/Truth two point mortise lock Patent number 6.264.253 and 5.820.170. Mounting holess 9 15/16". In stainless steel Thanks

Stamp: 14 2. Bsi Length: 14 5/8"

I need a 17-4 and 26-4 block & tackle window balancer.Thanks,Dan

I would like to completely replace all 4 handles, or if possible just the outside handles with something that actually has a handle on it that is not recessed (like the inside). I am willing to replace all four and the lock if necessary. The active lock side is the door on the right (when facing out ... (cont.)

Hi, Do you carry a latch that looks like this one?

Good morning, I would like to replace my existing handle set with your locking set on my brand new Pella 150 series door. I believe I know which handle set will work. My question is, do I also need to replace the mortise lock, since it is new? Or is your handle compatible? Thanks, Roger ... (cont.)