Viewing all customer Discussions for:

Door & Window

would like to get a replacement shoe for this shoe that is in a Loews 30 year old window.. the slot it is in is 1 1/2 wide and the thickness is 1/2 inch I measured the slot with a divider to a ruler..so its pretty accurate. i forget to measure the length, but it is about 2 inches long... any help ... (cont.)

the closest latch lever that I've seen in your website is Product# 82-240

I'm looking for two window balance replacements for a 19" balance with the stamp 19-5. The window size that the balance was in is 38 3/8" wide and 22 3/16" tall. I've attached two photos to show the balance and the top parts. Are you able to help me identify this part?

Like to purchase for window latches two left and two right? I'm attaching photos if you can look at the photos with measurements so I can purchase the correct ones for the owner

Does Swisco have the U-shaped gasket that surrounds the double glass Caradco double hung windows? These windows installed in 1982.

I have Hayfield windows that have the Truth 40068 operator and I am looking for new covers for the operator. A white operator Product Code: 39-138 looks to be a replacement operator but the screws are visible and there is a gap around the operator when inserted. Is there a cap for this operator or ... (cont.)

No markings or numbers

Hello! I'm looking for a replacement handle for this. I appreciate your help.

It's a two arm operator by entry guard truth. Model number 30842R I also would need a left. I don't know if they're different.

I need to replace the right hand tilt window latch. All the dimensions are the same except for the bottom "plate". Mine is 11/16" like the top but this part is 9/16". Will this part work for me?

The window balances I have are different than the ones I see on your website. As you can see, mine are springs with small plastic pieces on the top. The top piece has broke on several of my windows. Soooooo..... can you help? Do you sell any type of replacement or do you know where I might be able t ... (cont.)

Hello! Could you please help me select correct replacement hardware and handles for these windows? The long arm length is 9"Not just the arm mechanism, but what else would I need? Crank? Covers? Those metal plates that screw into the window? Can I use any screws to attach? As you can see these are p ... (cont.)

impervia series reinforced vinyl frame and sash door part number 83V0101 need rollers for this door I thought the part number was P-4998-FLR

Hi. I have 6 windows with damaged balancers, but I don't know what series they are or how to identify them. I would like to remove the top panel but I don't know the procedure. I am attaching some pictures in hopes that you can give me some advice on how to do the repairs. I will need to order par ... (cont.)

need balancer for anderson double hung window from 1987 size is 31 1/4 wide 25 inch high for each sash or window part I would need four for two windows , then I would two window balancers for anderson window 31 1/4 by 17 /1/2 high each window section

I need some white clips and a lock for my windows (pics attached), please send me the links for those items as well. Thanks, Thank you for the quick response. The white part is 1/4" W & 1/2" H very thin. Sorry I don't have one to take more pictures. There are two on each side of the window ... (cont.)

The lock although old still works but lever to operate it is loose. The entire mechanism should be replaced but for now only the handle to open and close is loose. There are no numbers for identification. It is an Andersen door. Thanks

Tried to use your site but it said my email was no valid. Attached are photos of what I need. Your site doesn't show the quarter inch lip to the right of the round tube. Let me know if you have the Pella seal. Thank you

Hi, I sent a request earlier and the pics would not load so I am resending it with jpegs this time. Thanks again for your help. This is the original one that broke they are on windows that are from Peach Tree around 2010. They are for wood with cladding on the outside. We would need may be 4 pair ... (cont.)

which non tilt channel balance model do I need to replace this? 27 inch long 1/2 inch wide code 26 4 FX CMC 11