Viewing all customer Discussions for:

Door & Window

19.5" long channelTop and bottom connectors are shown in photos. Stamp is shown as well. (19 5 BSI)Window manufacturer is InsulateI need 4 balances.

number stamped is 86 29-4 LA5 CMC 1 what item do I need to order ?

I need a replacement part for my backyard sliding door lock. I was recommended a mortise lock and a white handle set? Wanted to check and make sure I am ordering the right parts. Preference would be a latch that goes up/down to lock and unlock like my original (see attached), not a key. Hope to hea ... (cont.)

I am looking for a replacement for the roller in the photos please. I unfortunately do not know how to read a tape measure. That is why I included pictures with the measuring tape. And in the one photo the screwdriver is pointing to the tab that is on both sides.

Need lock and keeper for a pro 50 double sash vinyl window. Part is 23/4" long. See photp below

26-4 EN5 CMC 41 27" length of metal and 5/8" width it fits into a Stepped Sash Guide, Alpine product number 18-171. The actual sash size is 34 1/4" w x 28 5/8" h. I'll be needing about 10 balances and a couple of the sash guides. I've broken them when attempting to remove the balances so if you ha ... (cont.)

I need "constant force" type balances for a Pella fiberglass double hung window. Both sashes slip down in the track. Can these parts be replaced?

We have this sliding door in our house and i cant figure out the manufacturer to get replacement parts. The handle recently broke and we have tried lowes and home depot with 0 luck. The color match is also a huge issue. From the stickers on the door we capture ALI ADW-8 ASTM 2190. ... (cont.)

I'm currently trying to replace two window balancers from vandalism with a previous occupant of my property. The manufacturer from what I can tell online is Anderson but the only mark on the sticker says series: 200sh. Are these windows Anderson? Can I replace the window balancer if they cut the co ... (cont.)

The balance is 21" x 1/2" including plastic ends added to metal. The metal piece itself is 19 5/8" .

1. Length of metal channel is 19 5/8" 2. Stamp is 19 3 and to the side of this stamp is B.S.I. with PG to the side. I would send you a photo of the markings however I reached my 5 photo upload limit. 3. Manufacturer is Certainteed, all windows were installed when the building was built in 2006. 4. ... (cont.)

We are looking for this part in right and left for a BF Rich replacement windows. Can you tell me what part this is?

I have two (2) windows from Atrium where the seals have shrunk because of the sun.Each window is approx 3 ft X 5 foot. I need replacement seals.Thank you,Greg

Hello, I'm trying to locate some replacement parts for my house. The first is the balance clip for my windows. I found one on your website but I'm not sure if it's the right size. The second is weather stripping for my front door.

here are the photos of the balancers and sizes that i am looking for. if you can send me a qoute on these items in the pictures. Thank you. All Balances are for Non-Tilt Windows. The Width of the Channel Balances are 9/16 on the Stamp side, which is equal to 1/2".

I need white vinyl glazing bead with the following dimensions - approximately 5/16" (horizontal segment) x 9/16" (curved vertical segment) as shown above. 3' lengths would be fine. I need 8 pieces. This is for single hung vinyl windows made by "CA"

Hope you can help I am trying to a am trying to identify a 6 coil sash window balance set.I have 3 coils on each side. 2 of the coils have numbers on 8 and 4 and the third is unmarked.I have not weighed the window as yet. All 3 coils run down the front edge of the window slide to the coil balance sh ... (cont.)

I currently have vinyl windows that use the system in the pictures. Some of the windows are missing the balancers and I was trying to see if you carried the product. I spoke with someone at john evans sons but unfortunately they do not sell them in singles. After going back and forth with them they ... (cont.)

Hello, I have several failed Vetter sash locks that I'd like to replace for white ones. Would your lock #90-320 be the correct part? Thank you for your help, Maria McGuire

We have 25-year-old Jordan windows. The plastic strips that hold that glass in place are old and cracking. Is is possible to order replacements for these?