Viewing all customer Discussions for:

Door & Window

The subject operator is depicted in the attached photos with the handle removed and sitting beside it on the windowsill. These are awning style windows from a house built in Broward Count, Florida in 1968. I noticed the window was slightly ajar and when I went to close it, the screw mechanism that t ... (cont.)

HELLO I CAN'T FIND A LOCK SET FOR MY STORM DOORS.CAN U PLEASE HELP?

The 2 metal inserts broke. See photo. Do you have these available?

I have a few broken window channel balances. The windows are all non-tilt windows with 1/2? channels. I tried to match it to your channel balances and it appears to match your S380 series (with a 19-005 channel balance top and 15-005 balance shoe) Can you confirm based on the attached pictures?The ... (cont.)

Can you advise if you sell these parts that need replacement on my jalousie windows. Thanks!

These attach to top of climate guard windows to keep the windows latched into frames. Looking for replacements as many of them have pastic clip snapped off.

Can you please help us identify this item and if we can get from you Thanks

Channel is 1/2". Metal part is 28". My ends have no wings. Depth of bottom is 1 1/8". Ink stamp is 28 3 Caldwell FM. Whaddya think? You've helped me before, I hope we can do biz again. Thanks, Joe

Thank you for this site and for the option to post questions. I have twin seal single hung windows that have "MW" stamped on the latch. I'm not the original owner of this home that was built in 2001. Today there was a loud noise and I found the clip latch that creates spring tension broken at the to ... (cont.)

House built 1993 or 1994. Stationary top window, flange applicator need pivot locks believe it is 1/2 inch depth 2inches high by one inch wide. Which one is it.? House is built about 1993. Also need tilt latches. This is a picture of a tilt out latches which one is it on your site. We believe it is ... (cont.)

I have a 14" channel balance with only a metal stamp 14 2. It has the 1 and 3/32" base plastic piece.

I have a nuair DH-R30 900 series I need double sided channel balance for 3 windows, they are 35" the metal only the number on the channel is g 345 38, not sure what need to order will need to replace 2 per window x 3 windows = 6 channel balances. if you could advise on what model number I need ... (cont.)

Is this product made of plastic? - or is it made of metal?

We need channel balances for 12-year old Milgard windows. They are 1/2" channels, look like S380 or S385, also some of the others. They are 15" long overall, with 13 2 stamped on the channel. The windows are only around 22" wide.

I'm looking for new levers. Please see attached photos. I saw one on your site but the square hole underneath looks different, I don't know if it is the correct one. Can part number 90-247 be used? Thanking you in advance.Terry

Does this kit include the handles and the mortise latching set and lock? Also picture shows brass so wanted to verify this is a brass set?

We are renovating an old house and having trouble removing the sash for cleaning and painting. The marking on the crank housing says they are Semco. I have looked online to find information on how to remove them and while I have found information it doesn't seem to work on these sashes. The pin on t ... (cont.)

Hi, Please tell me what I need to order. I am replacing all the parts. I was unable to find any numbers or markings on the old parts. Thanks for your help! Carrie

it is 26 inch 2530 BSI window channel balance. I have ordered one before which has different plastic ends so was not able to use it. Please provide me with correct part number. I need two of those for my two windows. other side of windows are fine.

I ordered the 55-197 but not working just falls out This is for a sliding patio door, didn?t see that i could Order sample pieces until after $50 placement of order