Viewing all customer Discussions for:

Door & Window

I need 50 of these pivot shoes

Window from late 1980 marking says Truthnext to gear

I have three sliding doors where I want to replace the rollers. They were manufactured in Phoenix by Western Insulated Glass in approximately 1992. They are still in business but say they cannot identify the rollers. Your product 81-175 looks close but the wheels are plastic and I prefer steel. ... (cont.)

Any replacement suggestions? It is 1/2 inch wide by 25" and change long (image attached). Thank you!

Hi there, I have a vinyl double hung window that does not stay open. Upon removing the sashe I found the springs on both sides broken. The springs are 1/2 inch 7 lb hook end that I could not find anywhere. I wonder if I can use your S152-7 instead. Also, the balance shoes are plastic closed rectangl ... (cont.)

I'm trying to match an awning operator. Your 39-084 is almost an exact match. If the old arm extension is 2-1/8" verses the 2-1/4" on the crown, would it work properly installed?

Do you have this part with Steel wheels? Thanks

I am attaching some pictures of the parts. Please let me know if you can help.

Hello I need some parts for an aluminum single pane window they are the tilt bar which fastens to the side of the sash. All plastic fits on bottom corner and pictures included please. Thank you Mike

Hello! I'm unable to see the ends of your balance clearly. Can you turn them on an angle so that any "wings" on the attachments are visible, and then send more photos?I suspect the bottom attachment has wings, and I can see that the top attachment has none. I'm thinking that this is Series 351, Seri ... (cont.)

I need to replace two metal bifold door pins that have gone missing since the property was built in 1962. This is a photo of one of the remaining pins. Please let me know if you have these parts, and their numbers in your inventory, if you have them. Thanks.

Hello, I have a sliding patio door from the 60?s. The picture attached is if one of the rollers. As you can see, it has worn out to the point the door cannot be used. I don?t want to replace the door, but cannot find a replacement part. I have tried to alter rollers that I have gotten at Home D ... (cont.)

I need the tilt latches and lift spring for vinyl clad windows that were sold by Home Depot in 2011

Looking for the name or part to replace a few broken locks..

Thanks for your help with my problem.The pivot bar #26-129 (third picture) is correct. The pivot shoe #15-152 (first picture on right) is incorrect, the one on the left is the one I am trying to replace. Size is good except 17/32 thick would be best. The second picture is the old one, note the recei ... (cont.)

Hello,I am in need of 3 truth hardware tie bars. Here are the three tie bar lengths I need: 22.9 two roller (possibly supposed to be 3?) 34.9 Three roller46.9 Three rollerMeasurement is from the top of the tie bar. The top lock point is the same on all three. I can only attach 5 pictures. I ha ... (cont.)

Good morning, I have the same corners referenced above and believe either the 95-205 or 95-206 could work as replacements. Do either of them come in almond?

1720v 19"total 18"metal 5/8deep, 1/2 w need quanity 2.24B 26 1/8"total, 25" metal, 5/8 deep, 1/2 whide quanity 16.1120v 13" total 12" metal, 5/8deep, 1/2 whide quanity 2.I also need the stops at the topsome are white with a slid lock, and the original ones are black no slide lock. They measure top o ... (cont.)

The window brand name is Mastic. I do not know how old they are. I cannot open my window because the window falls forward as the locking mechanism is missing. I'm hoping you have a replacement part.

Hi, I am looking at replacing the sash lock in the pictures with a new pair in white. The keeper is angled like you can see in the pictures. The code inside of the keeper is A-S9227PA Thanks