Viewing all customer Discussions for:

Door & Window

Hello, I am attaching two pictures of sets of window coils that I need to order from you, can you please identify them for me. The only information on the coil is an F imprinted, I have no other information. We have vinyl tech windows. Can you please advise.This is the balance coil I bought from S ... (cont.)

PPG Herculite Trempe Tempered Can/CGSB

I am ready to purchase the series 350 as well as clips. I now need replacement glazing. I removed the existing glazing from my window based on your helpful how to video.. Please advise me as to which type to purchase so I may finalize my order and complete my repair. Super psyched. :) thank you ... (cont.)

Do i stand outside in front of the door to determine of it is a left hand or right hand opening door.

I sent a request about a week ago. Never heard anything. Can you please help identify this part for me

Hi, I am looking for the right channel balance for my window. In the old part, it is stamped as 2730F (pictures attached). I was looking at the following link: https://www.swisco.com/28-inch/pd/Series-351-Channel-Balances/S351-28 However, the top and the shoe looks different from the pictures I h ... (cont.)

Dear Swissco, I am looking for 6 replacement 1/2 inch Balance Springs for hurricane impact windows with a balance sprint model number of 29-14 CB5 CMC (29HP44-45). Please let me know if you carry this model and the cost for 6. Also if you have instructions on how to replace a balance sprint on ... (cont.)

I have tilt in replacement windows. They are between 15-20 years old. The upper sashes on two windows won't stay up. I removed these pivot shoes and I'm not sure what size replacement I need.

40055 T LH 4

I am looking for Snap on Vinyl glazing bead for Aluminum window (White). I don't know the part number nor the window manufacturer, I replaced the glass on a Florida Sun room and could not find the glazing bead for it. Could you please help my if you carry those glazing bead or help me locating one w ... (cont.)

Hi, Hope you guys can help me identifying the window balances I need. I need 3 sets of them for single hung non tilt windows. No manufacturer name on windows at all. Pics are attached. Overall length 24-13/16. Width 7\16 Depth 7\16 Markings: 23B (on one set) and 8 23BZ (on the other set) ... (cont.)

The window supplier is Chantecler, who is not in business now. Hope I can find a replacement.

Can you help me identify the correct tilt latch to replace this? I just purchased the condo that the windows ae installed in, and do not have a clue what kind of windows they are. The condo was built in 2001. Thanks, Jeff

I need drawer slide that allow open draw 12-1/2in. Draw itself: Deep: 18-1/2in. Slot: .25in. 1/4 in by 5/8 in. Drawer slider itself: 3/8in. by 5/8in. Please let me know which model correct one I need. Thanks

This balancer has a clip on the top; the ones that I have ordered from you have a clip with a hole on top as if I was to tie something. I've enclosed pictures of the code on the back of the balancer that I wish to replace, a close up pic of the top clip and a shot of the balancer that you sent wit ... (cont.)

This is the piece that fits into the part that pulls the cable when raising or lowering the window. I believe they are Keller tilt windows. Thank you Cindy

Please provide pricing for the below rod and cap. PGT Single hung window. 6SHSTKA / SH-4000. Window size 34.5 x 38 I think my balance is the Series 395. But The dimensions on my top sash guide are 7/8" wide across the platform, 13/16" wide on the body at its widest point. The screw holes are 3/16" ... (cont.)

Need replacement balance 24" options stamp 2420

Need new lock and key for wood slider. Inside with flu lock dimensions 3-3/4 x 1

Good afternoon. I need help identifying the proper balance for my windows. I am sending these photos as requested. If more information is needed please let me know. Thank you,