Viewing all customer Discussions for:

Door & Window

I purchased 26-369 but it is the wrong size. Original part is longer and has 3 holes equally spaced. Also has number 6240 stamped on it. Length is 3 1/8 inch. First hole is 1 5/8 inches from u shaped tip. 2nd hole used is 1 1/4 inch from 1st hole (middle hole not used). All other dimensions on the o ... (cont.)

Recently bought replacement latches for my new house that were missing. They were broken, now that they are installed they don't latch after windows is fully closed. It short like 1/4-1/8 is there anything I can buy to ensure they are locked rather than using the the screw at the bottom of the se ... (cont.)

Please I have door in my basement I need to add lock to door To fix with latch Thank you

Hi, I found this at another supplier but would rather order from you as you have the latches I need and I had a positive experience a few years back with a casement operator I got from you. Can't seem to find an exact match in your online catalog. I need six (6) but it's a teeny, tiny order. Sorry ... (cont.)

Hello help! I broke the thumb latch (see attached images) of my patio sliding door and need help to purchase a replacement. I don't know the manufacturer of my sliding door but I know it was installed in 2006. If I cannot obtain the part I will be willing to buy a full set including the handle a ... (cont.)

I would like to order some take out clips that will work with my 25" Series 380 Channel Balances. thanks, Brad

Hello, I need part numbers for both complete pins and brackets for bi fold doors as shown.

I need help identifying some white vinyl snap-in window glaze. The windows are nearly 25 years old installed in Scottsdale Arizona about 1992. I have attached a picture of the old snap-in although in the picture the snap-in appears much thicker than it actually is. Also attached is a jpg of the di ... (cont.)

Back Sliding door handle 7 1/2 inches x 1 1/4 inches 4 inches center to center (btwn screws) * The building plans we have do not identify the manufacturer, but list a model number 6067 sliding door. The actual door frame is starting to crack at the top corner of the handle, weakening it. We are h ... (cont.)

I would like to replace 8 hinges. They were installed in 1994. Cheers, Fred

I need four of these

Can you please help me identify my window latch as shown in the photos? My house was built in 1995 and many of the window latches have been breaking and I need to replace them all. Thanks K

I have 770 series and it id 22f I don't see a 22f is it avalible

please help identify for replacement on closet door upper guide thank you.

Manufacturer is PlyGem #3753. The broken release assembly is a LEFT hand side in black. The locking tongue is broken off during installation and the installer is long (3 years)since gone. The photos depict a right hand sample which was easer to photo than the actual left hand broken assembly. Ple ... (cont.)

Its a Alcan Double stormglass window. The black plastic broke. Its 1 inch wide and 35.5 long. When i take the window out it goes in first. Then the window can slide.

From PGT single hung. Guide is white thermoplastic, the number "5" the only embossed marking. Body width is 13/16 (width of channel on window frame). 1 9/16 total height. Thanks!

What sash lock can I use for my awning window?

Good Morning, My house is approximately 50 years old. We still have our original Pella windows, and they are in good condition. We recently had our house aluminum sided. Although instructed to go around the outside hardware, the contractor removed all of our screen stops on the outside. Pella no lon ... (cont.)

Looking for a wool pile seal replacement. This is on a Certainteed sliding window. The seal runs vertically and seals the edge of the window to the frame when it is closed. It is the inside/locking edge not the leading edge. It looks like it is a double seal- one section white and one grey. ... (cont.)