Viewing all customer Discussions for:

Door & Window

Here's a picture of a part from the side of my Patriot window. It is the same size as the one picture you sent 15-195 but it does not look like the picture you sent. My handyman said a small piece broke off of the end. There are tiny numbers in the piece. They are _AT #S 6.679.000 ... (cont.)

I have a Ryan home with what appear to be NVR manufactured windows, and the shoes for channel balances in 2 of the windows have broken. I ordered some 15-194 shoes, but they don't fit as the bottom of the channel balances look like they were squeezed. Can I order 4 of these balances with hooks at th ... (cont.)

The original channel balance is stamped 27 4 FW CMC 10 (IMG_3474, 75, 76). I believe the correct one is the 28" Series 390 Channel Balance with the 2710 option? Also I need two top sash guides (IMG_3471 and 3472) which I can not seem to find. Thanks, Ted

We have a number of Craftline sliding glass doors whose locking assembly is beginning to fail. Attached is a photo of the part and drawing of the part from the original instructions. Does this look like a part you would have in stock? Thanks, Michael

Trying to locate 2 Jordan window sash locks. 2 1/4" hole to hole with a 1" drop for tongue, comes out 3/8", white. Can you match this item?

I am trying to identify the proper Channel Balance. Alcan 2320E. I have attached copies of the top and bottom. It is the 1/2" channel and 24" long. The closest I have found is 24" Series 380 Channel Balance. Product Code: S380-24, Option 2320. Can you please confirm or assist in identifyi ... (cont.)

Do you have this part?

the house I just bought is missing the strike plate(I think thats what its called). the entire piece the lock goes into is gone. Do you have this part and if so how much and how long for shipping. Thank you

Casement Window Crank & Bottom Track Identification Request. Would appreciation any assistance that you could provide.

This is a device that permits the window to roll up and down. When turned, it locks the window in place if lifted. It has two parts; one of the parts has only a half

Looking for replacement retainer for storm door window. Can't find name or serial # . Had a wright brand door handle . House built in 1999 sandstone color full glass storm door.

I'm looking for the plastic mounting clips that snap into a 1/4" x 1/4" hole to fasten the top of a spiral window balance. The clips have retainer snaps on two of the sides to hold them into the hole.

Please help me to identify the proper latch for our Pella Windows that need to be replaced. I think it might be 90-243, but would like to verify before I order a few of them. Regards,

Marking on the old balance channel are 29-4 AA CMC 11

Looking for a replacement for this lock assembly. Would like one with a key if possible.

Do you know roughly how long is the protruding lock shaft of the 38-090? Is it around 1 5/8 inches? Will your 33-108 screw work on this handle?

My slider door locking pin sheared off. I cannot find another handle with the measurements. Do you have this pin? I can measure it. Thank you

Hi We need replacement Channel Balance for Single-Hang, Non-Tilt Window. Manufactured by: Binnings Pan American. 9/16 aprox: 1/2 ich Wide. It is 30 inch Long with Weight Code: 29-5 To be on a safe side please find Btm and Top Guide pictures attached. Are we right with Product Code: S377-30 ... (cont.)

Having trouble finding 1/4" screen corner

We have two patio doors from the same manufacturer. One of the doors seems to have rollers that are deteriorating. The pictures might help you identify them. FWIW, the subdivision is Preserve at Wynmar. The doors were installed early 2003 by the builder - Edgemoore. All of the windows in t ... (cont.)